Jump to content
SAU Community

Recommended Posts

hi guys i purchased a nismo 320 kph speedo for my 32 gtr and went to install it and it will fit but the warning lights are in different spots so i wasnt sure if it would work so i went to remove the speedo itself and install in my cluster, It is quite different and wont fit as it has an electrical ribbon connection that my one doesnt have, I have been trying to search on the subject but cant find the answer, if I just plug the new one in will it work or will there be issues?

Scott

Link to comment
https://www.sau.com.au/forums/topic/357773-nismo-320-kph-dash-install/
Share on other sites

Either find that guide as BWRGTR has said, or you can move the cables in the connectors on the harness. I worked it out a couple of years ago and wrote it down, but won't be home for over a week and a bit.

You can work out which pins need to be moved where just by working off the rear of each unit.. Just remember the speed signal out is polarity conscious.

Why can't he just remove the speedos from the two clusters and swap them? As r32 speedos are cable driven and not electric like the 33 onwards

the design between the two clusters (early vs old) is different, so once the speedo is out of one, its not a direct fit into the other unless the speedo sensors is swapped.. also possible to re-pin the connectors at the back which i have done in the past but the swap saves messing around with all the pinouts

the problem was you got a late model 32 cluster for an early model 32. they are different between years. and you can't just swap the speedo's between them as in is the 320kph and one is the 180kph so it won't work obviously.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...