Jump to content
SAU Community

Something Fell Of My Car And I Dnt No Wat It Is

smcqueen89

By smcqueen89,
in General Maintenance

 Share

Recommended Posts

smcqueen89 Collaborator

smcqueen89

Posted
  • Author
Posted

i looked in the engine bay and everything looks fine iv started the car im not sure if it was just laying around wit bits and pieces of the car of its vital to the car

its funny coz i just got the car last week and wen doing a service on it i have found parts just sitting in the engine bay eg turbo gasket

Nic_A31 Grand Master

Nic_A31

Posted
Posted (edited)

That's your AACV....car ain't going to idle or run without it....it should be mounted properly and hoses clamped on tight....very hard to beleive it just fell out.

Hopefully it was just another spare part laying around in the engine bay....

It mounts on your intake plenum around cylinders four and five, just below the throttle body.

Edited by Nic_A31
jiffo Mentor

jiffo

Posted
Posted

That's your Air Reg.(cold start fast idle valve)

Car will run fine without it PROVIDED the air hoses are re-connected properly.

Otherwise you'll have a huge air leak and she won't go.

My guess is it's been by-passed previously (aftermarket plenum perhaps) and finally decided to fall off.

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

It could be blocked off in the past and hence not affecting the engine. If that "were" to fall out, you'll have massive misfires, idle problems as it loops into the plenum.

Those usually fail all the time on RB20DETs and mechanics just block them off.

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

[quote name=ClutchBurndout-:(' timestamp='1300758954' post='5724847]

wait stop everything

u can block them off?

Correct, that's what mechanics so. Problem is sometimes on very cold days you might find you will need to slightly press down the accelerator to get the car to start.

The hose comes off the cross over pipe, into the AAC and back up into the plenum/TB. I've found out on several RB20s (including my previous car) that it was blocked off with a bolt.

Problem is when these AAC fail, no matter what you do, the idle is quite high. People often mistaken this for the IAC valve, spend hours adjusting idle, etc.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      RB20DE NEO smallbox clutch.

      By Duncan · Posted

      yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Duncan
      NC MX5

      By Duncan · Posted

      Quite right, if you make it to that pension you deserve every cent
    • jtha7
      Replacing turbo water line - any recommendations or advice?

      By jtha7 · Posted

      Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • MBS206
      RB20DE NEO smallbox clutch.

      By MBS206 · Posted

      From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • MBS206
      Lock up the old for sale / wtb threads.

      By MBS206 · Posted

      That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
×
×
  • Create New...