Jump to content
SAU Community

Recommended Posts

i looked in the engine bay and everything looks fine iv started the car im not sure if it was just laying around wit bits and pieces of the car of its vital to the car

its funny coz i just got the car last week and wen doing a service on it i have found parts just sitting in the engine bay eg turbo gasket

That's your AACV....car ain't going to idle or run without it....it should be mounted properly and hoses clamped on tight....very hard to beleive it just fell out.

Hopefully it was just another spare part laying around in the engine bay....

It mounts on your intake plenum around cylinders four and five, just below the throttle body.

Edited by Nic_A31

That's your Air Reg.(cold start fast idle valve)

Car will run fine without it PROVIDED the air hoses are re-connected properly.

Otherwise you'll have a huge air leak and she won't go.

My guess is it's been by-passed previously (aftermarket plenum perhaps) and finally decided to fall off.

It could be blocked off in the past and hence not affecting the engine. If that "were" to fall out, you'll have massive misfires, idle problems as it loops into the plenum.

Those usually fail all the time on RB20DETs and mechanics just block them off.

[quote name=ClutchBurndout-:(' timestamp='1300758954' post='5724847]

wait stop everything

u can block them off?

Correct, that's what mechanics so. Problem is sometimes on very cold days you might find you will need to slightly press down the accelerator to get the car to start.

The hose comes off the cross over pipe, into the AAC and back up into the plenum/TB. I've found out on several RB20s (including my previous car) that it was blocked off with a bolt.

Problem is when these AAC fail, no matter what you do, the idle is quite high. People often mistaken this for the IAC valve, spend hours adjusting idle, etc.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
×
×
  • Create New...