Jump to content
SAU Community

Recommended Posts

  • Replies 804
  • Created
  • Last Reply

Top Posters In This Topic

yes you would.

When i put a gen GTR bar on my 32 sedan, i used the R reo (cause i was told i needed to, and the bar i bought came with it)

The only thing you'll notice when putting a genuine R bar on is that the sides buldge out a bit, due to the gtst being not as wide as the R.

Hope that helps. (someone correct me if i'm wrong.

depends who you ask! some say yes and some say no, try thegtr bar on the gts-t reo before you buy

I dunno about that lol, I see masses of R32's everyday gettin around my area. Very close to the same amount of 33's I see. They are all common but I still think 34's are the least common, especially coupes. Do see a fair few 34 sedans.

must be an area thing, naff all 32s in midland ,altho there is a nice n tidy 32 sedan up the road on great northern hwy

finally finished my repairs from the hail storm.... personally i think it's looking even better than before it got all dented.

thats f**king hawwt dude, rims suit it so well. always loved black 32s, but gunmetal has to suffice lol

Pulled the fans and intercooler/piping off yesterday. Degreased + highpressured the piping/cooler and the engine bay then cleaned the cooler core out with some thinners.

This afternoon the cooler/piping and fans will go back on and probably trim the front bar and bolt that up too.

Radiator was ordered yesterday :banana:

Clutch was inspected and deemed to need an overhaul kit.. ~$650 for the kit but not available until next month!! So looks like I'm going to grab a new Exedy button clutch instead.

Ordered my tensioners and idler this morning from Statewide Bearings, NSK part numbers, VERY reasonable prices!

The only unknown at the moment is injectors... anyone got some GTR injectors for about $100?:P

Fans back on, cooler on and plumbed up.

HID's wired but only one fitted because my drill went flat fkn (typing this while I wait for it to charge)... what a cnt of a job, the retainers in the wagon would have been perfect but the retainers in the 32 required some "modification".

Bonnet latch & support back on and operating well.

Need to pull the reo off and give it a bit of a grind tomorrow, the dodgy hacking from the previous owner fouls the cooler in one spot :(

Oh and a successful NIStune fitting today on a 34GTT, drive in drive out :D

Ok lets see if this drill has enough charge fkn

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...