Jump to content
SAU Community

Recommended Posts

Hi everyone

I was hoping to see if anyone could help me out on the forum,i have a 2000 model R34 GTR and am in the market for an electronic boost controller.

Just wondering what would be the best one.......in the near future i'm hoping to be putting out around the 400awkw mark i have been checking out the HKS evc boost controller but don't know if it works well with the GTR's? any help or personal experience would be great thanks.

Link to comment
https://www.sau.com.au/forums/topic/358825-best-boost-controller/
Share on other sites

Good old bleed hole works a treat on GTR's.

I had a $600 odd AVC-R that just didn't work - workshop ripped it out and replaced with a piece of alloy pipe with a hole drilled in it off the wastegate lines. Bigger the hole higher the boost.

Holds 17psi perfectly (GT-SS ~14psi actuators)

I do hear the newer dual solenoids are much better as Ash mentioned, but no point if it can be done for a couple of bucks. Is also tucked away out of sight, no screens and wiring harnesses to install etc.

as ash said you only need a good controller if you want to run MORE boost

if you get the right sized actuator spring or external gate spring at the desired level then that's all you need

no need for a $500 controller. its only if you want to bleed MORE boost over the minimum target level that you need a controller

the higher priced controllers usually offer scramble, dual solenoid, fancy displays etc

if you insist on a controller dont get a 14psi spring and try to run 27psi

its too much work for the controller and it will struggle, try and size the spring according to your minimum target level

ie if you want to run 19psi all the time, then get a 16psi spring and bleed 3psi

Thanks guys for the quick reply's

The main reason i want to install the boost controller is because i want to be able to control a high and low setting hence dual stage.

I had a Greddy pro-fec b 2 in my tt supra and i liked the fact i could drive around on 10psi all day then when i felt like giving it a boot full i can switch it over so it has a max of 16psi thats all.....Wanted to get something similar but was not sure if their was one that worked really well with the RB26

Speaking from experience alone, went from a pos his evc5 in my evo to a profec b spec 2 and was far happier.

Also went from blitz SBC to turbotech in a 32gtr with factory position twins and was also MUCH happier.

The turbotech has never disapointed nor failed. The profec is also quite a nifty toy with a couple of valuable features for a lightly modded car.

Be it myself I would do the right foot boost control with actuators set as close to target as possible and a turbotech for added confidence on spool and gate creep.

best value is profec B II. they work fine on GTRs and are cheap and easy to use.

best outright is either HKS EVC 5 or the BLITZ dual SBC ID3. both very good but more costly.

as the guys said if you want say low boost of 18psi, get 15psi actuators and bleed 3psi, then for your high boost you'll have to bleed a bit more. I can understand wanting 2 boost levels, nothing wrong with that. and the best way to get that is with an EBC. either of the 3 above should give good results. I've used all 3 (and others) personally in my cars.

I have a profec b spec II in my car at the moment, it works great (was cheap second hand) and has 2 boost levels but I feel that the Blitz dual solenoid ones work better at holding boost dead flat, plus the Blitz ID3 has 4 settings.

I have also used Turbotech bleed valves on various cars and once they are set up (they can be a bit fiddly and sensitive) you seriously can't beat them for price. Only issue is they only have one boost setting.

Edited by SimonR32
  • 3 weeks later...

They only do if the gate is creeping/opening early.

I used to experience it with my external as an example

7psi spring - 17psi bleed. Gate would "creep" open before 17psi.

15psi spring - 2psi bleed. Gate would remain shut until 17psi

:)

Sometimes internal gate setups suffer this also as the gate is much smaller (eg ext 45mm, int 25mm).

But it varies and is influenced by quite a few things including dump pipe, exhaust restriction, lengths of vac hose/where you are referencing boost etc.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...