Jump to content
SAU Community

Recommended Posts

Hi All,

I've been trying to find safe/normal operating temperatures for an RB25det, a good idle seems to be about 80c, but what is considered a safe temperature when you start pushing or tracking the car?

After just fitting a replacement engine to my 33 I've been watching the temps very carefully, my dash gauge never moves above 1/4 no matter how hot shit gets so I've been using a consult cable to read from the ecu, currently running water through the system as the engine has only been in for a couple of days and I'm checking for leaks etc. City driving sees 80-86c, I was at wot in 3rd for 15-20 secs heading up a steep hill right after a spirited drive and temps reached 98c, obviously water becomes fairly useless at this point so I just coasted down allowing it to cool.

Is +100c normal for an RB being driven hard? If so I guess I should switch to some coolant asap.

Link to comment
https://www.sau.com.au/forums/topic/359460-rb25-operating-temperatures/
Share on other sites

You talking stock radiator? I wouldn't be tracking with a stock one. I mean you can in a stockish car, but its not really ideal.

With a aftermarket radiator, my RB25 and RB26 both sit between 67-75 putting around. Only giving it an absolute gut full will see upwards of 80+

IMO invest in a radiator if you are see 98, thats up there.

  • Sad 1

Hi All,

I've been trying to find safe/normal operating temperatures for an RB25det, a good idle seems to be about 80c, but what is considered a safe temperature when you start pushing or tracking the car?

After just fitting a replacement engine to my 33 I've been watching the temps very carefully, my dash gauge never moves above 1/4 no matter how hot shit gets so I've been using a consult cable to read from the ecu, currently running water through the system as the engine has only been in for a couple of days and I'm checking for leaks etc. City driving sees 80-86c, I was at wot in 3rd for 15-20 secs heading up a steep hill right after a spirited drive and temps reached 98c, obviously water becomes fairly useless at this point so I just coasted down allowing it to cool.

Is +100c normal for an RB being driven hard? If so I guess I should switch to some coolant asap.

I have an R34 - usually runs 85-89c - on hot days it runs 90-103c depending on load.

Hard driving on a moderate day is low 90s

I'm running Castrol 33% coolant.

My car is stock.

Edited by iseekool

Normal street driving on belter hot days, the highest I've seen in either car was 95deg, nothing to worry about.

The 32, on a 40+ day and a good 2 min skid, the highest I've seen is 105deg which was fkn hot but still didn't throw any coolant.

Coolant, under pressure, isn't going to boil until about 110deg. If you're seeing about 100deg or higher on the street or highway, then you've got issues that need addressed.

From my experience, RB's like to operate at about 80deg (RB20/25non-neo/26), they run a 76.5deg thermostat. The neos seem to want to run a bit hotter (probably due to emissions reasons) and they run an 82deg thermostat.

Edit: I also had way better results from a stock GTR radiator than the 50mm chinese alloy thing I used to have.

Edited by bubba

I have an R34 - usually runs 85-89c - on hot days it runs 90-103c depending on load.

Hard driving on a moderate day is low 90s

I'm running Castrol 33% coolant.

My car is stock.

It's worth noting that R34 have a much higher thermostat than the R33 (off the topic of my head I beleive it starts opening around 80-82C and fully open by 95C?). I believe these hotter running temperatures were done as part of the LEV modifications (ie: lower emissions) ..

My R34 sees similar temperature ranges as above on a stock radiator (using tectalloy 100 coolant), fresh thermostat, recently changed fluid, etc. Planning to put a bigger radiator in within the next few weeks. I will note I saw much higher temperatures (105+ on hot days stopped in traffic) when I had a nismo radiator cap fitted - not sure why that is.

Coolant doesn't make your engine run cooler, all it does is increase the boiling point. In fact, due to Ethylene Glycol being an oil product, it actually reduces the thermal efficiency of water. Only products that reduce surface tension are going to reduce temps

  • Like 1

I boiled all the water/coolant at my last track day. Would have been 120degrees PLUS.

Hopefully my dedicated RB26 r32 sedan track car never sees boiling point, not a nice feeling wondering if youve ruined your engine.

If I didnt have a thick headgasket on my RB25 (stock bottom end, ported head, gt3076) Im sure it would have shagged the engine......

It could be your stock radiator is blocked with sludge. best to replace it with a thicker dual/triple core aluminium 'race' item. The one in my

RB26 is from ASI in melbourne @52mm thick, the RB25 radiator is a Koyo 40mm thick item

Thanks for the replies guys.

I have an R34 - usually runs 85-89c - on hot days it runs 90-103c depending on load.

The NEO does run a bit warmer than the earlier 25's, my thoughs were inline with R31Nismoid and bubba, for a '96 RB25 I was expecting to see 80-90c but had never monitored it after a hard drive to know for sure.

Current radiator has had various mixtures of chemiweld and oil through it in a previous life, even though it's been flushed it's probably rooted. I guess I'll be looking at an aftermarket radiator for peace of mind :thumbsup:

nissan thermostat for all RBs except 34s is 76.5C, but the thermostat is in the bottom hose (coolest point), temp sender is in the top hose, which is the hottest point of the system.

i see the same temps as nismoid, high 60s to low 70s, but thats not normal, seams to be a 31 thing.

I always thought it just to be a 31 thing with added space in engine bay and around the front of the car aiding airflow.

My GTR does as well though with a decent after market rad, which I found interesting and dispelled that one.

  • Sad 1

Mine sits at ~82 during a normal day without A/C & will go up a couple of degrees when stuck in traffic.

In a 38C+ day with A/C on, it will go over 90C when stuck in traffic but will drop back down to about 85 when moving at decent speed again.

This is with a stock radiator, recently got the plastic top tank repaired & rad cap and thermostat replaced.

  • 3 months later...
  • 7 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
×
×
  • Create New...