Jump to content
SAU Community

Help With Finding Where This Wire Is Meant To Go.

L0Ki

By L0Ki,
in General Maintenance

 Share

Recommended Posts

L0Ki Enthusiast

L0Ki

Posted
  • Author
Posted

It shields heat...

Not hugely important but if your running a inboxed POD filter you would be getting alotore hot air sucked in from the engine bay

haha thanks!

But seriously is there a problem with the wire not being connected? Should i bolt it to somewhere else? Is it actually an earth?

I;m more worried about the wire not being connected causing problems.

Thanks for the help so far.

stig mick Veteran

stig mick

Posted
Posted

I know mines not connected as I have an aftermarket du pipe and the heatshield wouldnt fit

It hasn't caused any problems

But I would be interested to know what it's grounding

karma_syke Collaborator

karma_syke

Posted
Posted

haha, when i read the title of the thread i wondered if it was the same 'wire' that confused me, and it was!

i was missing a heat shield, it had disappeared (i think) when the turbo back exhaust was installed along with the dump pipe shield. not that it matters cuz it wouldn't have fitted the new pipe anyway,

i attached it to a bracket which held the original heat shield. i imagine its an earthing wire.

L0Ki Enthusiast

L0Ki

Posted
  • Author
Posted

Yea i' dont wanna remove it, Id much rather connect it then take it off afterall it wouldnt be there if it wasnt important. Its just that it seems like the end that isnt attached should be attached to something immportant (i know the heatshield) but the end that is cconnected just seems to be earther on the chassis?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Ethanol Content Sensor - Always at 11%?

      By joshuaho96 · Posted

      The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • GTSBoy
      R34 Skyline climate control unit transistor

      By GTSBoy · Posted

      It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • GTSBoy
      Blue slip

      By GTSBoy · Posted

      South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
    • bilbo117
      R34 GTR Seats / No longer reclining

      By bilbo117 · Posted

      Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • Dose Pipe Sutututu
      Ethanol Content Sensor - Always at 11%?

      By Dose Pipe Sutututu · Posted

      Those above shitboxes, mediocre and above usually have a turbo strapped to them, hence the slightly higher octane is required.  
×
×
  • Create New...