Jump to content
SAU Community

Recommended Posts

Just completed a re-build:

JE 87mm pistons

Tomei OGK - 1.2mm

ARP Head studs

Cosworth Bearings - Std

Tomei Poncams - 260/260

Apexi PFC - D Jetro

Koyo 4 core Radiator

N1 oil pump

Mishimoto 62c Thermostat

GT2860-5 Turbos

Mines Titanium DP

3.5" SS Jasma Exhaust

Car runs well and maintains water temp in the 70s and oil temp in the 80s when driving.

Problem is when idling for more than 10mins, water temp rises to 90c+. If the car is parked soon after, about 200ml of coolant flows out of the expansion tank.

Advice?

Link to comment
https://www.sau.com.au/forums/topic/361704-rb26-rising-temp-advice/
Share on other sites

you might have a basic water pump issue or some sort of flow issue

90 isnt that bad, but it shouldnt move past 90

ask the engine builder?

the n1 water pump flows less at idle vs stock as its designed for high end RPM high flow

so at idle, it will actually be outperformed by the std water pump in terms of flow

when did this start? since the radiator change?

check the basics etc

Would an N1 water pump help?

not really.

You've gone a put a part in thats not fit for the application - a 4-core rad.

As you've stated it's perfectly fine when driving, and it will be... Or more importantly track - which is what i'll guess it's designed for. Not street.

I could be wrong, but all bets point to the rad as the issue.

You might have not bled it correctly or something and have air lock/bubbles. But i doubt it.

I built the engine myself and it definitely goes past 90, but if I keep the revs up above 2k, it drops slightly.

The problem started after the re-build which is the same time I installed the new rad.

Already bled the system twice. No change.

Is it a 53 mm koyo radiator? If it is I have the same on my r33 gtr

I have never had a problem like this, normal driving temp is at 66 deg n when at idle in traffic it may only move 1 or 2 degrees

Thermostat only determines when the water starts circulating. Once it is open it has no effect on max temps (only minumum temps in a very cold climate). Stock would be better as 70deg is not hot enough. Have you got a shroud for your fan? Fan doesn't do much without one.

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • How dare you sell your unreliable Skyline and buy a reliable, Toyota/Yamaha car with a strong gearbox, torsen LSD and Toyota reliability. At least you won't need to worry about oil pumps, big catch can, oil restrictors, blowing off power steering belts, sheering off 3rd gear, failing ABS relays/pumps, etc.
    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
×
×
  • Create New...