Jump to content
SAU Community

R32 Gtr Rear Attesa Leak

R31_GTSX
 Share

Recommended Posts

R31_GTSX Rising Star

R31_GTSX

Posted
Posted

Hi all, I have a fairly substantial leak coming from the rear attesa system.. I have stuck my head under there and there appears To be the attesa unit above the diff and there is a lot of fluid on a wiring plug coming out of the unit. Has anyone got any pics of the unit out of the car and if it is possible fluid is coming from a switch?

Any help would be great!!

Thanks

Link to comment
https://www.sau.com.au/forums/topic/362375-r32-gtr-rear-attesa-leak/
Share on other sites
  • 2 weeks later...
R31_GTSX Rising Star

R31_GTSX

Posted
  • Author
Posted

Thanks endless, mine looks like it's leaking from the other side, looking from the drivers side just in front of the diff. Thanks for the pic.. It gives me a much better idea of what I'm looking at. Did you take this off the car without taking the diff out? Or did you need to remove the diff?

I'm not sure I can fix the leak with it still on the car.. I'm dreading having to take it out though.

endless Proficient

endless

Posted
Posted (edited)

That's not my picture, just a borrowed one!

You have to remove the diff to get to it. I will check mine on drivers side to see if it is wet there, mine is a pretty decent leak too as it drained the reservoir last time enough for the 4WD light to come on after a short time (only just got the system working due to other issues)

Unfortunately for me, i have JUST replaced all the diff mounts so i had access to it but didn't know it was leaking! :(

Edited by endless
R31_GTSX Rising Star

R31_GTSX

Posted
  • Author
Posted

Mine is the same, I fill the reservoir and within a couple if days it's almost empty... Leaving behind a trail of everywhere I've been over the two days. The light is on and I haven't refilled it, of late because it empties too quick. Is it possible the unit would have Shat itself with no fluid? I'm thinking when I get it off I should probably just replace it with a known working unit. Problem is getting the car off the road as I have no spare..

endless Proficient

endless

Posted
Posted

Pull your 4WD fuse for now as this will stop it from leaking out any more fluid. I'd think the unit would be working as long as you didn't run it bone dry. I'd bleed it once leak fixed though.

Just checked drivers side on mine... looks dry. Mines definitely the other side.

endless Proficient

endless

Posted
Posted

Ahh, after some more searching think i have found my problem;

http://www.skylinesaustralia.com/forums/topic/328036-r32-hicas-pump-pressure-switch-replacement/

I found the bleed mico was talking about, here is a useful bleeding guide showing location.

http://www.skylife4ever.com/2011/01/bleeding-attesa.html

R31_GTSX Rising Star

R31_GTSX

Posted
  • Author
Posted

Great work mate, i look forawrd to getting the sucker off and having a look at it. If the fluid is traveling along the wiring then that could be my problem too. I reckon before I take it off I'll fill the reservoir, jack it up and then remove the white clip under the dash to actuate the pump.. Then just hope I can see the leak and be able to get to it with it still in the car. I hope the pump is still working!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      sold listed as a Tomei LSD 1.5 Way For 1998+ Nissan Skyline ER34 25GT RB25DE w/Open R200 https://www.ebay.com/itm/174006114594?campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=&mkrid=711-53200-19255-0&loc_physical_ms=108689&loc_interest_ms=&campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=71883f2ccc571356e0a757bc7adfdde2&mkrid=710-53481-19255-0&loc_physical_ms=108689&loc_interest_ms= it went in like butter all gears, alignment, back lash etc, rotation and clearances correct, and if rolling all rotates smooth and free when coasting down road , clutch in or out over 10 mph smooth... its the binding, clunking and jerking from a stop that is most concerning, also seems like its going to tear the tires off in 10 miles of normal road driving. 
    • Kinkstaah
      new 1.5 LSD issues/concerns

      By Kinkstaah · Posted

      What 1.5 way? There's no such thing really as a 1.5 way, just different ways of explaining 2 ways with different ramp rates. HOWEVER. In any driving in a straight line your 1.5 or 2 or 1.7 way should have no clunking at all. With the clutch fully depressed the diff should be silent (unless it's welded but I'm assuming it's not). Something aint right here.
    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      Clutch is a spec brand, new clutch system,( PP, flywheel, friction disc, etc. pull type) installed 100 miles ago, with no problems.
    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Matt Z
      SAU NSW - Archies Flame Grille Meet & Cruise to Kurnell

      By Matt Z · Posted

      Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
×
×
  • Create New...