Jump to content
SAU Community

Recommended Posts

still just a maybe at the moment Erin , will find out in afew days when the line will be ready ! Any more info about the SAU QLD club , will it be starting on that day as well ?

  • Replies 232
  • Created
  • Last Reply

Top Posters In This Topic

I need to buy a UHF radio, im thinking about getting one of the good transciever kind.

So i have a scanner aswell, boostcruising i think it is lists all the different areas police frequencies. Would be pretty cool to be able to see what 'they' are upto for once.

Cheapest one is like $300 tho

just need to check my budget status again (mostly current homeloan) and if all goes well i will have the GTR within 2 wks. I currently have one that i have had my eye on for over a mth now. Getting the car inspected this saturday, so fingers Xed.

PS: R33 :rofl:

just have to add i was at bwcp for the last one and got chills when everyone arrived, nothing better then seeing and hearing a line of skylines down shifting down the hill to turn into the car park, i had the r31 for that night!!

Providing I can get my car down here by then( its STILL in Mackay):P I will be there....although i will break the tradition of the round taillights as i still cant find any for sale in japan

We are actually going to make a detour on the way down to stop for hopefully what might be some really good pics.

Hopefully cyrus wont chase rabbits and we won't be scared out by security.

And the rule still stands, be a wanker, your not welcome. Especially at this point in the cruise.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Here is a recipe. Sonic blocks till you get one that has a good enough bore. Get a torque plate and block brace, use your choice of fasteners (arp ect) bolt the thing together empty, half fill it and let it cure. Release it when it has, go to a REPUTABLE RB Builder and get the thing line bored/honed and cylinder honed to size, then wash. Once its all clean and dandy, wash and blow it out again. Then again.  Assemble said engine to your desired clearances with oil control mods, gasket to suit desired CR/Squish ect. Attach your extended sump with proper trap door oil baffles and head drain plumbed to sump with a SUMP BREATHER SYSTEM. Build your front diff with a decent LSD, rebuild your transfer case with a few extra plates, more than likely replace your tailshaft centre bearing and tighten up the rear diff. Tune to minimise excessive midrange cylinder pressure (timing unless you like to split bores and rebuild engines) Enjoy your engine, but hate the fact you are now destroying engine mounts, gearboxes, gearbox mounts, diff output flanges and driveshafts, diff mounts, tailshafts and front CV's.   Disclaimer.... Ive never done any of the aforementioned stuff.......
    • 440s will support well over 400HP on petrol, which is a decent place to be for an RB20. 230+rwkW. Will be a safer bet for idle/low load. 550s would be nice for the extra headroom. I've made the same decision with mine (Neo25). 1000s are probably too big for the Nistuned ECU, so I have some smaller ones.
    • Appreciate everything guys. I did go ahead and get an alignment... most of my complains are solved. Car is not perfect, but it's good enough. If I notice uneven tire wear or anything I'll just take everything back to stock.  Thanks again!
    • They still have not shipped the 550cc injectors as they weren't in stock, so in theory I could ask to get the 440cc ones instead, if those work better in my scenario. They're the same price so really shouldn't be an issue. Unfortunately I am not so knowledgeable in most parts of tuning so I wasn't sure what's best to choose between the two. 440cc ones are the lowest they have (not in stock, but available to buy nonetheless).
×
×
  • Create New...