Jump to content
SAU Community

Recommended Posts

Wanted to sell

RB25 gearbox conversion package.

Suit rb or sr/jz with adapter plate.

Located northwest.

$1600 ph 0409 631 092

Full package, had good oil, no swarf, drove excellently. 145xxx km behind stock engine with dampened clutch.

-one gearbox with shifter and all sensors

-clutch slave

-tailshaft

-all bell housing bolts

-crossmember and mount (R33)

$1600 ph 0409 631 092

RB20, 25, 30 clutch and flywheel

Located northwest.

$800 ph 0409 631 092

ORC-409D-01N (R32, R33)

The ORC 409 Single Plate Metal Clutch Kit Nissan is the Competitive Single Plate Clutch kit by Ogura Racing. The clutch is the damper type which will maintain streetability and handle up to 400ps in addition to having excellent engine response with the lightweight chromoly flywheel.

Throw out bearing/carrier/sleeve, flywheel bolts and clutch bolts are included.

Heaps of meat left, have driven this and other Orc 409d, epic clutches, easy to drive but heaps of bite. Basically "the" drift clutch in Japan.

$800 ph 0409 631 092

  • 2 weeks later...

Looking for a good condition R32/S13/Z32 etc adjustable Passenger side rear camber arm. Will buy new or second hand and will buy a pair as well if someone has anything kicking about? 0401739292

Edited by tobs_r32
  • 1 month later...
  • 2 weeks later...
  • 2 weeks later...
  • 5 weeks later...
  • 2 weeks later...
Needed Urgently:


- R32 GTST standard drivers seat belt buckle (I would consider whole drivers seat if not willing to separate).


- R32 GTST headlight projector globe clip (this holds the globe and attaches to the headlight via a circlip type clip that then connects to the headlight loom).


Located Hobart but happy to pay for postage, or travel.


PM or 0439182091

  • 1 month later...
Wanted, set of r33 gtr wheels, tyres aren't a huge concern. I would prefer to buy but I also have a set of 17x9 +10 work meisters I might be willing to swap

Your meisters.... How much ?

:)

1992 R32GTR

T51R SPL 24psi

Apexi power FC

OS Gikken quad plate

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...