Jump to content
SAU Community

Recommended Posts

  • Replies 3.6k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

So the latest with my car is that I dont think its the turbos. After finding some long fingers and taking more pipe work off they spin fine with no play. The swirl marks that I saw from down the mirror where just fine oil and dust.

Going back to the cat it wasn't collapsed but it has a bit of carbon build up in it. Would this cause a huge restriction. It also has a blue tinge to it so it suggests its getting hot. After the shudder the exhaust note was quieter.

If I had blown a turbo I would of thought I wouldn't get any boost?

Im still getting 10 out of the 20 that it was set to. Plenty of pressure on the wastegate.

Ive checked all pipework and boost hoses. Car still starts and drives ok it just wont get the boost it used too.

Have I missed something before I put it all back together? Or do I need to pull more apart. I havent checked the back of turbos they are N1s so I would think the wheel is still there.

If I were you Brad I would take the GTR for a quick burn (very late at night) with the exhaust and cats removed and see if it will make 20psi. If it does, then it rules out the cats or collapsed exhaust out of the equation.

Bit of work done today. :)

Motor in, then gearbox in, now tomorrow to cut intercooler holes :)

nice!

ps: on your yahoo travels luke, can you keep an eye out for a 4" hks super drager cat back for a jza80 for me ? do u know how much they go for...need 1 real soon...? Thanks.

Bit of work done today. :)

Motor in, then gearbox in, now tomorrow to cut intercooler holes :)

Good to see that thing getting together now. Will come and lend a hand/have a beer with ya when I am free mate :D

I just worked out the cause to my boost problem. It was a half blocked cat. There was a fair bit of carbon build up. It was very black inside. The cat should be a nice brown colour inside from the carbon being burnt off. Anway did the cowboy thing and bashed it out. Now the car boosts even better than before.

Since were talking about tunes. Should I get my car tuned again? Only because last time it would of had a part blocked cat. And now it flows better.

I always thought running N1s @ 20psi would get more than 265awkw.

not sure if anyone has read this about iphones/devices, but really apple didn't test them in australia based upon the temp restrictions did they ? even outside the car they get over that hot ?

Apple over temp warning

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...