Jump to content
SAU Community

Recommended Posts

  • Replies 3.6k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

We were asked/ordered by SAPOL to take down the thread about the cruise, the subsequent thread and all references to the event. Even they don't like how the news/ACA grab hold of these things and publicize the hell out of them - it actually makes more work for them. Various media outlets were hounding them daily for more details, and they were browsing SAU constantly for info. Best solution for all import owners is not give them any ammo.

and on the note of ammo, I just deleted 2 stupid posts from the "Spotted Thread"

why give even an inch to the law makers and media when we're trying so hard to keep up appearances (so to speak)

An off the cuff post (that may seem innocent) can have long term efects as to how all of your rides are viewed by Sapol & the media

If you have 1/2 a brain in your heads, engage it before posting :wacko:

We were asked/ordered by SAPOL to take down the thread about the cruise, the subsequent thread and all references to the event.

Figured as much. Probably wasn't the smartest thing to post on Youtube. We had an event in WA on Sunday called 'Rising Sunday' - similar to All Japan Day. WAPOL camped out near the exit and defected around 20 cars..... things aren't much different over here to SA!!

Skip to 55 secs for the 'Hoon Report'!

Edited by 32godzilla

dont you guys realise that no matter how you play this. which high road you take.. that the cops and not to mention the pollies and poweres to be have already mapped out how its going to play out.

they are talking about putting in a recommendation to the magistrae that the cars be forfieted.. all because of some public f**king image.

i dont care what opinion you all take on the guys that did the tunnel runs but this is just a f**king bullshit abuse of power/governmant.

thats my rant for the night.

so by your definition Simon, doing the opposite (ie run a muck on the roads and put all sorts of shit on Youtube) wouldn't make any difference then

We all need to be wary of what ammo we give Sapol & the Media.......to say it won't make any difference is not realistic unfortunately

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...