Jump to content
SAU Community

Recommended Posts

Much cheaper than the kit they copied though. Much like their Geomaster knuckles... Speaking of which, if they retained standard ackerman angle, I'd be all over that shit. 50mm drop spindles FTMFW.

  • Replies 3.6k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

I've just got rid of HICAS because the rear was out of control.... Was just doing whatever it felt like

Yea thats what i was going to suggest, bout to do the same on mine actually, rear is a little unpredictable at times.

just jap have a lock bar for i think $100, and looking at the DIY it doesnt look extremely hard to do.

Did you just chuck on a lock bar?

Driftworks have a nice kit that replaces the ball joints etc and all, bit costy though :/

yeah just a lock bar, it wasnt that hard to do, but you need a wheel alignment after, had some pretty epic toe in lol. I just adjusted it visually for the drive to the alignment place.

those that may not have Nene in their facebook here is one of her status updates a very grim warning

Janene Fulcher

At Elizabeth Centre when putting your children on the little rides. If an Old Lady comes up 2 u & starts poking her tongue out Sexually at your children Report her straight away. When my mum & I said we dont do that she kept going & i mean sexually poking her tongue out she then tried to get closer and closer to sienna & we are not exactly sure but it looked like she was going to pick her up.This happened to a friend of mine today! it is being treated as an attempted abduction by police. Janene

stage 2....pfffftttt

more car less camera Dave

Should be sufficient for the power I'm chasing. Don't need new springs and such with these either.

Hahahah, yeah... Now that I realise that money could've covered new wheel bearings, I do slightly regret it.

Slightly.

lol,

fitting up mine in a fortnight and cant decide to tune on flex or not. pros: it would be awesome and most likely make 310-320 ish. cons: that power would be useless, and if towing plans fall through for winton id have to take 400L with me. lol

those that may not have Nene in their facebook here is one of her status updates a very grim warning

yerp that my was daughter that Nene's talking about...Luckily the wife and mother in law were onto it!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
    • The BES920 is like the Toyota Camrys of coffee machines. E61 group head is cool, however the time requirements for home use makes it less desirable. The Toyota Camry coffee machine runs twin boilers and also PID temp control, some say it produces coffees as good as an E61 group head machine.
    • And yes with a full tank it will hit limiter free revving or driving 6B6CDF6E-4094-426D-A9CB-6C553475FE36.mp4
    • One way of putting the fuel surge idea to rest, is that even when in neutral/clutch in or free revving it still has the same issue, it can’t even get to limiter (7800) so to me that says it can’t be g force, I’m not trying to argue I just want to find the f&$king issue 😡
×
×
  • Create New...