Jump to content
SAU Community

Recommended Posts

Bosch EV14 1000cc ID1000 style

These are a 3/4 length injector, 14mm Oring, top feed, high impedance, UScar style plug.

Tuff Car Parts can sort you out for those Adrian

steve i want anything 1000cc that will fit under my plazmaman!! LOL

status said those side feed are highflows

  • Replies 3.6k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

i want to convert to top feed as they are cheaper/bigger cc/easier to find.

if i can find some genuine 1000cc drop in side feeds ill get them.

its either top feeds dont fit or side feeds are hiflows or not avail!

FML

Wow the Aussie dollar is in freefall after the USA debt bailout announcement - $1.10.7 2 days ago, has just bottomed out at $1.07.0 - better buy up any parts you want from overseas now kids!

Eyebrow height is the one point, but there are others, like "the distance between any part of the

vehicle and the ground is not less than 100mm."

It should all be documented in the following:

http://www.transport.sa.gov.au/pdfs/personal_transport/light_vehicles_pdfs/MR1136_Requirements_for_Lowering_or_Raising_Vehicle_Ride_Height.PDF

http://www.transport.sa.gov.au/pdfs/personal_transport/light_vehicles_pdfs/fact_sheet_track_suspen.pdf

9yWXX.jpg

Anyway, familiarise with the above, and call Regency Park - you may even get a straight answer.

If they abolished eyebrow height you could technically be on the tyres with 100mm clearance still, and one would think that you need some sort of clearance between guard and hub to allow for adequate suspension travel, so logically, there should still be a eyebrow height law, in my head anyway...

My V35 is the opposite - I have bucketloads more eyebrow clearance than legal/desired and my exhaust (which has been modified already to be as close to the car as possible) is still way under 100mm clearance and bottoms out on EVERYTHING :(

Pretty sure that is all that is sold in Aust'. Infact i think they are all HSPA+.

when i was looking they were about to release the 4g. that was 2 weeks ago. so wuld have been out by now..

i would have got it but im with optus!

and steve i watched that yesterday when i signed up to xda... LOL

Currently doing the 4g roll out on all existing towers at my new work, you probably won't see proper 4g Australia wide for another 12 months. They might release 4g phones now but they will probably just run at 3/3.5g

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...