Jump to content
SAU Community

Recommended Posts

Hi SAU, I need your help / suggestions...

Took my car to my tuner today to get my ignition timing advanced a few degrees, (road tune only) we found that my R34GTT leans out gradually after 5000rpms, sometimes around 4500 onwards, no matter how much fuel my tuner is adding, it still does this.. I have also noticed previously that it dosen't have any top end (its constant and smooth but not 'weld-me-to-my-seat'). That was with our previous tune. We then loaded the stock R34 maps and started from scratch and it still does this even with the stock maps.

As a matter of fact, we backed off and will be taking it to the dyno next week to check if the fuel pump, fuel reg is playing up? Now the pump is a new Walbro GS3442 that was installed and re-wired not more than a couple of months ago, it has a factory sock which has a bit of play where it meets the pump. The car has the usual FMIC, exhaust, 12psi (which holds constant from 2800 onwards), cold airbox, Nistune. So I will be driving in low rpms for now hehe..

Someone please throw in your suggestions as to what could be the cause of this?? ECU retarding timing in high rpms?? We detected no knock thank god, never did, even with previous tunes.. Fuel pump?? I hope not, its the newest item on my car, and it gave me a lot of noticeable power gain after the install, more than anything else.. Fuel reg?? what what.. :(

Could it be my AFM is dirty? - its the stock one.. BTW just wanted to add that before the Nistune and fuel pump, my car was hesitating and had the flat spot at this SAME 5000rpm band - something like 4700-5700rpm - a flat spot zone, Nistune has fixed that, the flat spots gone, acceleration is smooth but theres just no power in this zone - ie I dont feel the turbo pushing me hard in my seat..stock turbo 12psi... before I could feel it, from 6000-7000rpm it felt the strongest then.. And now this leaning out from 5000rpm onwards..

Having a read here:

http://www.evoxforums.com/forums/archive/index.php/t-35897.html

one guy says:

"Don't rule out a bad sensor for your AFR guage. The last two I had fail both started reading lean by almost 3 full points. Funny thing is, they would read okay in closed loop, just not when you got on it."

another says:

"Try ur fp relay first. I seen another post with a guy using blue fpr, same problem, switched to syock, problem solved"

and the answer is:

"found the culprit it is a missing fuel freaking pump relay in my fuse box in the engine bay ! i took the horn relay and put it in the fuel pump relay and my afr was PIG RICH.

really weird and i dunno why evo x over here does not have a fuel pump relay.

been busy @ work but will load up a map and see what happens from there on.

but nevertheless i will double check all hoses again but afaik everything's tight and will do another full boost leak test.

will keep everyone posted soon."

How good to have internet and good people!.. But I still havent found my answer yet.. duh

Connect a fuel pressure and flow guage and monitor pressure and flow while its playing up.

Will save you a fuel pump if theres plenty of pressure and flow.

Also monitor response of the fuel reg - could have a hole in it and not increasing rail pressure with boost.

If he knows what hes doing, your tuner should know to do all these things without you having to find out for yourself on the internet.

One is a dampner Ron.

Need to get it on the dyno with the fuel flow/pressure tester as discussed with u. Its extremely unsafe to do this on the road.

I need to check ur install on the fuel pump. Last time this issue went after filling the tank full.

Have even loaded the fully stock factory map and the issue is still there

Ur car had the same or similar issue with ur old tuner and old fuel pump.

Wiill get it sorted for u. Just harder because u cant leave the car with me

Have heard pple sayin to check the afm, but if that was dirty, we would get less clean air into engine per unit of fuel which means its running rich, but its not, its the opp ie, running lean, dont understand this one

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...