Jump to content
SAU Community

Recommended Posts

  • Replies 91
  • Created
  • Last Reply

Top Posters In This Topic

I cannot give specifics, yet a friend with an R34 GTR seemed to get very mediocre results from them.. As do the evo community.

Personally I would stick to the known road with this car, RB26 has been done to death.

bought them off an american site paid 2950 included post full kit....\

um i also just bought and getting fitted

700 cc sard injectors

tomei full pump

apexi djetro ecu getting rid of air sensors coz there on there way out just a cheaper solution...

hks cam gears

tomei pon cams type B

full custom 3.5 inch exhaust

tomei bellbouth dumps

nismo fuel reg

standard internals

fair standard upgrades needed for the turbos recommended by tomei on their site...

theres a standard r34 gtr in japan with standard internals just these basic upgrades that are needed pushing 500hp with these turbos

bought them off an american site paid 2950 included post full kit....\

um i also just bought and getting fitted

700 cc sard injectors

tomei full pump

apexi djetro ecu getting rid of air sensors coz there on there way out just a cheaper solution...

hks cam gears

tomei pon cams type B

full custom 3.5 inch exhaust

tomei bellbouth dumps

nismo fuel reg

standard internals

fair standard upgrades needed for the turbos recommended by tomei on their site...

theres a standard r34 gtr in japan with standard internals just these basic upgrades that are needed pushing 500hp with these turbos

did u have to pay any import taxes/ duty? what was the site?

I'm planning on using this kit along with vipec engine managment , 700cc sard injectors, tomei steel head gasket & walbro 255 fuesl pump!

between 400-500 awhp would be nice, not too fussed with numbers, as long as it will run a mid 12 on street tyres & i'll be happy!!!

U got ur turbos yet? mine are in the post somewhere between here & there lol

Edited by tufftruckin

should do that easily. a stock GTR with just exhaust, boost and a tune (250kw) will run low 12s on stock turbos. stagea is a bit heavier but with aftermarket turbos it should be more like low 12s or 11s.

id have to agree with GTScotT, i remember one gtr with twin tomei turbos and it looked horribly laggy (5.5k) for the 350kw or so it made!! they were done to death on evos and know all evo owners shy away from them, one sr i saw with tomei arms had a similarly laggy poor result. id stick with the tried and tested garretts imo

should have gone hks for that money

what makes hks any better?

no one on here soo far has actually seen this particular kit in action,

maybe tomei's figured out their previous kit wasn't soo flash, so they went on to developed this improved model!

will soon find out if I bought a dud once they are all fitted and tuned!

between 400-500 awhp would be nice, not too fussed with numbers, as long as it will run a mid 12 on street tyres & i'll be happy!!!

U got ur turbos yet? mine are in the post somewhere between here & there lol

yeah i got them being fitted now just waiting on my nismo twin plate they should make 500awhp on 1.3bar thats what it listed on a japanese gtr with the m7655 fitted

id have to agree with GTScotT, i remember one gtr with twin tomei turbos and it looked horribly laggy (5.5k) for the 350kw or so it made!! they were done to death on evos and know all evo owners shy away from them, one sr i saw with tomei arms had a similarly laggy poor result. id stick with the tried and tested garretts imo

tomei just revised their range these turbos came out march this year meant to be on boost buy 4- 4500 rpm so with some good cams and cam gears and a good tune hopefully see good results will soon see next week..

never know if you dont give it a go i guess

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...