Jump to content
SAU Community

Recommended Posts

So finished rebuilding the engine , got Arias custom made pistons in it for neo engine ! when it was freshly finished it showed 120, 120, 130, 125, 130, 120 psi in all six cilinders . drove about 700km and now in all 6 cilinders is 120psi, same in all!! i have putted tomei poncams as well ! gasket is standard size standard has 9:1 as far as i know what number i have now? is it too low?

my friend owns RB26 he did same (forged it) and his car shows 145psi in all six?

so am i ok or in trouble? :))))

Link to comment
https://www.sau.com.au/forums/topic/369488-rb25-det-neo-just-forged-it/
Share on other sites

Normally bigger cams will drop your compression when you do a test, in comparison to standard. But not that much, especially with poncams. Did you build it yourself or an engine builder do it for you?

You did have the throttle fully open when you did the test?

my healthy neo with pon cams reads 100 psi all round lol

This is why I was persistently asking you about this.

110psi across all six here, with a new engine with poncams which I thought was pretty low but it runs great.

Using the same tester on an a standard RB26 which had 165-170psi across all cylinders then a built RB26 with big cams; 160-165psi :mellow:

Edited by aleks

Normally bigger cams will drop your compression when you do a test, in comparison to standard. But not that much, especially with poncams. Did you build it yourself or an engine builder do it for you?

You did have the throttle fully open when you did the test?

didn't touch the throttle and didn't cut the fuel :) lol i'll try to do that way :)

Glad that here is people running that low CR with no problems:)

thx

you sure?? cause mine is as high as 170 and 175,

100psi is low, that must be pretty unresponsive on low revs??

I really doubt its compression is actually almost half of yours, if it did it would drive like absolute shit, either completely wrong pistons or blown rings. The reality is it is probably one motor was cold/hot, different tester, different rpm, different cams etc.

My old rb20 measured 90-95 on all 6, made 155kw on 11psi stock turbo and blew no smoke, all that matters is it is close.

Edited by Rolls

thats just it.. too many variations to be able to compare one to another.. the main thing is all cyns are the same, and comp testers fall into the same bucket as dynos.. just a tool.

well i wouldnt be happy them just all being the same, id want to know its perfect after spending all that money rebuilding an engine,

a compression guage shouldnt be more than 5% different to the next , thats like saying a tyre guage says its 40psi but another is saying 30psi?

must be quite a big gap with forged pistons when there cold and the cam must be quite long duration to justify a 70psi drop after a rebuild, but just my opinion,

but if your happy with it then great..

thats like saying a tyre guage says its 40psi but another is saying 30psi?

actually happens a lot more than you'd think and more than 10psi a lot of the time, especially at servo gauges

also dont forget, static compression is different to dynamic compression, way too many variables to go comparing readings. as said aslong as they're all within 5-10psi and its not using more oil than fuel its fine.

Edited by JonnoHR31

well i wouldnt be happy them just all being the same, id want to know its perfect after spending all that money rebuilding an engine,

a compression guage shouldnt be more than 5% different to the next , thats like saying a tyre guage says its 40psi but another is saying 30psi?

It isn't just the compression gauge though, it is cam timing, actual compression ratio due to pistons, if they are forged, if they rings aren't yet bedded in, if you have a big cam, all of these will change the compression.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...