Jump to content
SAU Community

Recommended Posts

Hey guys i have a series 2 RB25DET with a cracked ringland and cylinder scoring in cyl 6. Head is all ready and prepped,so now i just need a new bottom end. looking at a neo engine to use. are the bottom ends the same? Will a series 2 head go on with no dramas or is it best idea to just convert to the whole neo?

Excuse my nubness on this matter.

Cheers in advance.

Thanks mate

If i were to put a neo in my 33 what complications would i run into? I would be using my series 2 RB25DET manual box. would the ecu run the r33 dash and everything else?

Or am i able to use my series 2 loom and ecu?

Edited by Blueone

You need the Neo's ECU to run the engine. I know nothing about S2 dashes (is there anything strange in there that relies on somethign special from the ECU? I expect not.) but would not expect any huge hassles. Tacho outputs are simple. Your gearbox will work fine. You may well need to rewire a number of plugs on the engine loom (I have to for Neo into my R32 - but they may be the same between R33s and R34s, I just don't know). Find a workshop who has done it before and it should be trivial - unless you want to do it all yourself.

If yours is a late series 2 with the palstic cam angle sensor then the motor should go straight in. May need to change the injector plugs

Nah its a December 95 series 1.5. So,close to one of the youngest series 2 engines.

then pop a 1k wrecker s1/2 rb25 inthere and use the good head for the 30 build...

1k you reckon? Hmmm.

Would be a good idea but no 30DETT i have built will have a 25 head or a big single :D

Edited by Blueone

yuo can adapt the R33 loom to run the Neo. Roll's did a similar thing.

all the RB;s from 20/25/26 can be adapted to run any RB loom. just takes some work and swapping of sensors and plugs to match the ECU.

idealy tho.. use the neo loom and neo ECu and then get a nistune on the 34 ECU... win

I'd be looking through aftermarket piston catalogs to find out what the dish volume is like compared to an R33 RB25DETs and if they are same or very similar go for it .

If all your R33s sensors interchange in the R34 block I don't see negatives , the positives are younger and potentially fresher pistons/rings/bearings depending on mileage .

As was suggested a cheap RB30 with fresh rings bearings and a hone could be cheaper again , just need some welding on the heads face and its off anyway . Done carefully it may not cost much more than a "runner" RB25 .

A .

yuo can adapt the R33 loom to run the Neo. Roll's did a similar thing.

actually an r32 with r32 loom, but yeah apart from that exactly as you said, just a few r33 bits thrown in.

actually TPS was the only thing that had to be changed.

Edited by Rolls

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
    • Oh, and as for everyone with their fuel economy changes, I switch between E10 and 98 in the company car. Even do when I had personal cars that could run on E10. You know what changed my fuel economy in any noticeable way? How I drove, and where I drove. Otherwise, say on full tanks of just back and forth from work only (So same trips, same sort of traffic), couldn't notice a difference that I can correlate to the type of fuel in use. In the current vehicle, that's over 42L of USABLE fuel. While 98 is all "more energy dense", it also has higher knock resistance as it takes more energy to get it to ignite too. The longer hydrocarbons, typically more tightly bound. So running the same ignition map, can also produce less power, if there isn't enough time to get it all burnt through properly, as yep, the flame propagation speed is different from lower octane fuel to higher (Higher has a lower flame propagation, due to the more tightly bound and harder to self ignite funs. This is also typically where, a vehicle that is designed purely to run on 91 (Whether it be E10 or normal 91) usually sees absolutely no real world difference in fuel economy for the normal man, woman, or dog.
    • We've got some servos around me that have 91 with E10, 91 (no E10), 95, and 98. At those stations the change from 91 E10 to 91, is typically around 8c/L.   But lets not get started on the price of fuel in Oz. It's ridiculous. All the service stations around me, bar one, the price of fuel has been over the $2 mark per litre for the cheapest, 98 being around $2.45. That one service station is a CostCo, fuel from it comes from the same refineries, and makes no pitstops, it runs great, including the 98. In fact, I've had no issues on CostCo fuel, but plenty of issues at other stations!. The CostCo fuel, was $1.65 roughly this week for 94 with E10. $1.88 for 98. Servos directly across from it, $2.10 for 91 E10, and $2.48 for 98. The part I had to laugh at? If I drive multiple HOURS away from Brisbane, say out near Nanango, or Kingaroy, or even out to Goondiwindi, the price of their fuel, is the same as what it is at the CostCo... Oh, and that BP servo at Goondiwindi is HUGE and goes through epic turnover of fuel, so it's not sitting there for weeks going to shit. And what blows me away, my mate is one of the people who drives the Fuel Tanker all around QLD, delivering to all those places. At the same company his previous role was doing the "local haul" deliveries... Same truck, same driver, same pickup point it all comes from. So you tell me, how the hell it is 60c/L CHEAPER for fuel, when nearly all else is equal, except they require a B-Double to drive half a day out of Brisbane, and half a day back, every second day, compared to the delivery that can be under 30 minutes drive from the fuel pickup point... Not to mention, go five blocks down the road, and Ampol to Ampol will vary 30c/L... And I've had this conversation with my mate... The way it's priced, is just typical, pure and utter rubbish... He also does runs from Brisbane, to all over QLD, down to Newcastle, Sydney, Nowra, Melbourne, Geelong, and even out to parts of the NT depending on the companies needs. His main stuff is all the longer distance away from home for a few days at a time, then when he's back, he loves to just pickup extra shifts wherever he can in whichever truck, hence all the weird different places.   Oh, as for getting E10 into all the fuels in Australia... It was very quickly highlighted, that we don't have enough biomass available to use to make E10 sustainably like they require, and it would dramatically cut into our, and the worlds food chain supply...   I vote we all just start running on liquid methane gas... Plenty of that just getting tapped off at tips from underground decay... (Note, this is pure just stupid commenting. I could very easily highlight the reasons its not a good idea especially on scale...)
    • Am I correct in assuming that the R35's are getting the classic skyline haircut off the odometer?  Quick search on carsales, there are 33 08 and 09 GTR's for sale, only 2 of them have more then 100,000km's on them (116,075 and 110,000 respectively).  And somehow there are about 25 for sale with around 60,000kms? Looks like the classic skyline haircut to me =/
×
×
  • Create New...