Jump to content
SAU Community

Recommended Posts

We can produce both powers at the same rev by adjusting the throttle plate.

Timing would be correct for the application at both loads.

If the AFR is the same fuel usage will be double.

However, I do believe I was caught up in the moment and using the word "exactly" may not bet totally correct.

There are many factors that come in to play like the difference in barometric pressure, air and fuel temp from the 2 events being 100hp and 200hp.

If measurable there would have to be some sort of variation.

The real concern is why your turbo is kicking out? I would be upset if my 3037 was doing that

More revs means more inefficiencies due to friction in all the moving parts, different revs mean different intake speeds due to the cam (which is why torque changes and isn't always the same) on boost, off boost changes things as well. The same power at the same AFR can be COMPLETELY different.

More revs means more inefficiencies due to friction in all the moving parts, different revs mean different intake speeds due to the cam (which is why torque changes and isn't always the same) on boost, off boost changes things as well. The same power at the same AFR can be COMPLETELY different.

Torque changes through the rev range due to changing Volumetric Efficiency.

i dont get whats so "lol", you do realise that its a street turbo usually you dont go over 5000rpm, i can deal with the 500rpm unlike having a lot of lag.

A street turbo that comes on @ 4500rpm - when you don't go over 5000rpm?

500rpm band... awesome.

Let's not forget more RPM when connected to a gear = more vehicle speed = more resistance = greater load on the engine to maintain that speed...will change with inclines and declines of road surface too. Way too many variables!

i dont get whats so "lol", you do realise that its a street turbo usually you dont go over 5000rpm, i can deal with the 500rpm unlike having a lot of lag.

Lol. On drugs much? Who says you don't usually go over 5k in a street turbo car. Especially wierd when we're talking about RB engines where you can scream to well over 5k in less than a second in 1st and 2nd....and usually do so.

More revs means more inefficiencies due to friction in all the moving parts, different revs mean different intake speeds due to the cam (which is why torque changes and isn't always the same) on boost, off boost changes things as well. The same power at the same AFR can be COMPLETELY different.

I do believe i said the same revs for different power.

You should actually read my post before replying.

Lol. On drugs much? Who says you don't usually go over 5k in a street turbo car. Especially wierd when we're talking about RB engines where you can scream to well over 5k in less than a second in 1st and 2nd....and usually do so.

im running a GTX3076r soon so i dont really care i never take it on track so below 5000rpm is good enough beside if i tune that badboy properly i can achieve about 480hp which is very decent for a street car. Another mans eat is another mans poison.

The same power at the same AFR can be COMPLETELY different.

What uses completely more fuel.

An Ls1 5.7 NA at 12.5:1 making 370rwhp

Or a CA18 turbo at 12.5:1 making 370rwhp?

Now we are talking massive measurable differences here so the answer should be very clear.

I have no idea, would come down to many factors... valve train friction, the v8 has more valves, pushrods, but each piston is lighter, the turbo car has higher VE but less cylinders.... Id flip a coin imo.

Probably go the LS1 because of more conservative cam profiles/emissions laws when the motor came out.

Edited by Rolls

but the LS1 has more volume, and needs less load per liter to create the the same power.

In a perfect world would have a smaller throttle opening but generate the same power.

So you can tell me, on the same engine creating 2 different power out puts that fuel requirements per horsepower are COMPLETELY different

But you cant tell me that with 2 completely different engines, creating the same horsepower your not to sure what one would use more fuel?

So you can tell me, on the same engine creating 2 different power out puts that fuel requirements per horsepower are COMPLETELY different

But you cant tell me that with 2 completely different engines, creating the same horsepower your not to sure what one would use more fuel?

I'm not sure if this is a serious question? How on earth am I meant to know the different efficiencies of the two engines? It involves hundreds of things! All I said is it would be different...

More revs means more inefficiencies due to friction in all the moving parts, different revs mean different intake speeds due to the cam (which is why torque changes and isn't always the same) on boost, off boost changes things as well. The same power at the same AFR can be COMPLETELY different.

Its not a serious question, Its a trick question. Its also a demonstration to show that statements like the above shouldn't be posted unless you know exactly what you are talking about.

Both engines use the similar fuel. most would say the same fuel. both do it in COMPLETELY different ways.....

But both use very similar fuel quantities.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...