Jump to content
SAU Community

Recommended Posts

I'm looking at importing an R32 early next year before the import regulations change, so at the moment i'm doing as much research as I can into exactly what I should get. I'm still debating whether or not it's worth paying the extra amount to get a GTS4 vs a GTST.... what do you guys think? What concerns me is that if I go for a GTS4 I will have less overall vehicles available to make my choice from. Also, fuel consumption will be worse, and I'll lose more power thru the drive train, which I can't really afford on a 2.0 l engine. Would it still be worthwhile or should I stick with a GTST and get a nice one?

Any other advice or suggestions as to what to get would be gratefully accepted.

Link to comment
https://www.sau.com.au/forums/topic/3716-r32-gtst-vs-gts4/
Share on other sites

ionos, the 4wd system (ATTESA) is computer controlled. the car is in full rwd mode unless it is putting power to the front wheels, so dont really worry about the fuel consumption. Control the fuel consumption with your right foot.

with the gts4 you can just pull a fuse out and go rwd only (as ABU53 / LA LA does...often) and i have seen ATTESA save him and the car from, well, doom. so it can be a pretty handy thing.

gts4 is heavier, if you want to get good throttle control and like rwd, go for the gtst, if you want the different (more advanced?) driving experience ATTESA can give, go for that. if the rear starts to go you can still turn in, as power will be fed to them. drive both.

good luck big fella.

Link to comment
https://www.sau.com.au/forums/topic/3716-r32-gtst-vs-gts4/#findComment-60843
Share on other sites

if you can get the GTS4 i would go for that. Just like a baby GTR.

Also, if you are importing, I would be careful that plates dont run out. I have heard rumours that there are less than 25 r32 plates left in victoria.. as I said , rumours tho, so i wouldnt know.

go here for a bit more info re the new scheme: http://www.prestigemotorsport.com.au/indupdates.html

dave

Link to comment
https://www.sau.com.au/forums/topic/3716-r32-gtst-vs-gts4/#findComment-60886
Share on other sites

I may be biased but I would definitly recommend the GTST.

They are lighter and you have a greatly balanced car.

Just keep in mind that, YES, you do get better launches with the GTS4 but I am sure that the GTST would catch and pass it down a quarter.. also, there is more to life than quarter mile runs..

I think that the RWD/front engine design is still the best and has the best balance.

Link to comment
https://www.sau.com.au/forums/topic/3716-r32-gtst-vs-gts4/#findComment-61431
Share on other sites

Maybe i too am biased, but life is not all about launching the car.. once you're off the line the GTSt will kill the GTS4... big weight difference. Less stress on brakes etc with the weight of the GTSt too, tighter around the twisties too i'd wager.

For the right price, you could have my R32 GTSt :D

Link to comment
https://www.sau.com.au/forums/topic/3716-r32-gtst-vs-gts4/#findComment-61471
Share on other sites

Thanks for the advise guys! I think a gtst would be the way to go, my logic is for the extra amount that a gts4 would cost, I could get a nice gtst with a few mods, that would go just as hard. I'm driving a front wheel drive at the moment and i HATE it, just can't wait to drive a powerful rwd car again.

Now I just hope that when it comes time for me to import, there are still plates left. :D

Morgs, what do you have, and how much? :) I wouldn't mind paying a bit extra for a local sale, but all the private sales i've seen in SA want $16000 + which is an absolute joke for a r32 (in stock form).

Link to comment
https://www.sau.com.au/forums/topic/3716-r32-gtst-vs-gts4/#findComment-61474
Share on other sites

The GTS4 comes standard with 4 spot front brakes (well at least mine did) and I've driven both, owned a GTS4 for 3 years and driven various GTSt's over the time. In the dry, on the twisties, the GTSt's are slightly better. They are also slightly better on rolling start drags or overtaking due to less weight. For every other situation, the GTS4 absolutely OWNES the GTSt. Wet weather is so much better with the '4 as is any non tractable surface. I remember towing a bogged 60 series Landbruiser with my GTS4 :) I had to get him 10 meters and my car did it with style :)

Now the brakes, oh god were the 4 piston calipers with ABS bloody good. Oh yeah, all GTS4's come with ABS standard, thats very well worth considering. Problem is, if you reef the handbrake on mid corner, the ABS unlocks the back wheels and 4WD engages trying to deliver identical torque to all wheels :D

One thing I learned with the GTS4 is how to drift and stay safe. With the GTSt's it's easy to go too far and spin out, the GTS4 pulls power to the front wheels after you start drifting and you get such a wonderful sensation of drifting and knowing there's so much more room before you get to the limit. I had adjustable KYB suspension in my car and it handled brilliantly, better than most GTSt's but the GTS4 is front heavy and tends to understeer much more than the GTSt's if you aren't gently powering through the corner.

Another great memory I have of the GTS4 is tying both towing hooks at the back of the car to a tree, putting some oil under all 4 tyres, in first, smoking them all up, almost redlining at 60km/h I pushed the cruise control button, opened the door, stepped out, took a photo of the car with all 4 smoking up, jumped back in and disabled cruise control :)

I ended up selling the car, pretty much in perfect condition with 103,000km on it for $9500

Link to comment
https://www.sau.com.au/forums/topic/3716-r32-gtst-vs-gts4/#findComment-61675
Share on other sites

Argh the options. Slip mentioned that the 4wd was only engaged when the rear wheels lost traction... does that mean that you will not lower power thru the drive shaft when it is not engaged, or will you still lose more power like all 4wd's?

Also, how much heavier is the GTS4? I'm a big guy :D, and with me and the girlfriend in the car, it's gonna be a lot of extra weight on that poor 2.0 l motor.

Link to comment
https://www.sau.com.au/forums/topic/3716-r32-gtst-vs-gts4/#findComment-61704
Share on other sites

Originally posted by Bozz

Another great memory I have of the GTS4 is tying both towing hooks at the back of the car to a tree, putting some oil under all 4 tyres, in first, smoking them all up, almost redlining at 60km/h I pushed the cruise control button, opened the door, stepped out, took a photo of the car with all 4 smoking up, jumped back in and disabled cruise control :D

Baaaahahahahahahahahahahaah

Bozz - you are officially now a legend. I love your work..

Link to comment
https://www.sau.com.au/forums/topic/3716-r32-gtst-vs-gts4/#findComment-61732
Share on other sites

Originally posted by Ionos

Argh the options. Slip mentioned that the 4wd was only engaged when the rear wheels lost traction... does that mean that you will not lower power thru the drive shaft when it is not engaged, or will you still lose more power like all 4wd's?

Also, how much heavier is the GTS4? I'm a big guy :D, and with me and the girlfriend in the car, it's gonna be a lot of extra weight on that poor 2.0 l motor.

yep, u shouldnt lose power as bascially it functions like a rwd until the rear wheels start to lose traction.

Link to comment
https://www.sau.com.au/forums/topic/3716-r32-gtst-vs-gts4/#findComment-61750
Share on other sites

Regarding the Brakes on the GTS4..

The GTST type M also comes with 4 pot calipers and ABS.

Dude..

Read these 2 articles, then decide for yourself..

GTS4

GTST

Then decide for yourself.

Every person on here is going to say get this or get that because that's what they have.. this includes me.

But read up on both machines and choose for yourself after driving both.

IF you can find a GTS4...

It's pretty hard to come by one of those and when you consider that for the price that people are asking for a 90 model GTS4, you could get like a 94 R33, it's hard to go past the R32 GTST (my opinion once again..)

Good luck in your search..

Link to comment
https://www.sau.com.au/forums/topic/3716-r32-gtst-vs-gts4/#findComment-61865
Share on other sites

And that's in Japan..

So finding one in Aus let alone a good one, is next to impossible.

As for GTST's there are always some for sale..

I've seen them as low as $13K (stock and pretty average)

Up to as high as (I personally think too much) $22K for one that has the GTR body bits and good engine mods and looks and so on.

Link to comment
https://www.sau.com.au/forums/topic/3716-r32-gtst-vs-gts4/#findComment-61936
Share on other sites

Originally posted by Ionos

Morgs, what do you have, and how much? :D I wouldn't mind paying a bit extra for a local sale, but all the private sales i've seen in SA want $16000 + which is an absolute joke for a r32 (in stock form).

Its a gunmetal grey R32 GTSt, exhaust, filter, suspension, the usual mods, and pricewise looking at about $16K. Put it in the TP for $17K but mostly time wasters from there.

Link to comment
https://www.sau.com.au/forums/topic/3716-r32-gtst-vs-gts4/#findComment-61949
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...