Jump to content
SAU Community

Recommended Posts

Hey guys, just wondering if there is a way to calculate rwhp from 1/4 mile trap speed, and what time this car would be capable of with a better takeoff. My clutch was slipping on anything harder then a 2000rpm launch so i could never take off quickly.

weight: 1430kg

ET: 15.017

Trap: 97.22mph

60": 2.348

Link to comment
https://www.sau.com.au/forums/topic/372424-rwhp-from-14-mile-trap/
Share on other sites

Try this Formula it works out the same as Moroso power calculator<br style="-webkit-box-shadow: none !important; "><br style="-webkit-box-shadow: none !important; ">Need speed and vehicle weight with driver<br style="-webkit-box-shadow: none !important; "><br style="-webkit-box-shadow: none !important; ">.00426 x MPH x = = x weight <br style="-webkit-box-shadow: none !important; "><br style="-webkit-box-shadow: none !important; "><br style="-webkit-box-shadow: none !important; ">.00426 x 118 x == x 3400 = 431.8 , same as Moroso if you set speed and check against weight.

Vehicle weight must be in pounds (2.2 pounds to a Kilo) and it gives rear wheel horsepower

So in your case it would be

.00426 x 97.22 x == x 3146 = 223.49 HP

Try this:

http://www.race-cars...calculator.html

1430kg= approx 3,153lb

I got 226rwhp (166.2rwkw) for you using that page.

I used this page with my Rx7 just to see when I took it to the drags and it wasnt too far off

Edited by Scottydoo

Try this:

http://www.race-cars...calculator.html

1430kg= approx 3,153lb

I got 226rwhp (166.2rwkw) for you using that page.

I used this page with my Rx7 just to see when I took it to the drags and it wasnt too far off

I have always used that and same, it has always been close to what the car has run.

Having said that though, it should be used as a guideline only, as ratio's play a major factor in E.T.

Ye ratios make a big difference indeed.

When the OP said 1430, given its a N/A 300ZX - i simply based off my time of around 1500kg as there is no way a 300zx comes in @ 1430 with a driver :D

I still say 130-140rwkw with that MPH for a 1500-1550kg car

Ye ratios make a big difference indeed.

When the OP said 1430, given its a N/A 300ZX - i simply based off my time of around 1500kg as there is no way a 300zx comes in @ 1430 with a driver :D

I still say 130-140rwkw with that MPH for a 1500-1550kg car

My 300ZX is 1430kg without driver :D Since its the slicktop 2 seater version(no targa tops, no un-necessary electronics etc). It came in at 1506(or so) on the weighbridge with me in it. Diff ratio is 4.08 if it makes a difference?? Since i have a new clutch going in soon, do you guys think a mid 14 would be on the cards?

Edited by Super Drager

that calculator is bogus, it says my car has 700rwhp, it has 500.

r33 with 10.8 @ 135mph.

It has probably been designed with a limited range of data, most likely the more common horsepower cars, eg 2-400hp range, your data is probably an outlier in the equation so of course it won't work for all cars.

All it is is a line of best fit.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...