Jump to content
SAU Community

Recommended Posts

Im no longer campaining a skyline with an RB engine anymore so im selling off some of the gear that I have no use for

There is nothing wrong with any of these parts, they either dont work with my new engine package or are not up to the job I need them to do.

Fuel System gear Aeromotive 1000hp pump. Brand new unused in new box$400

Aeromotive inline fuel filter 10 micron Brand new unused in new box$150

3 Litre surge tank to suit above pump and filter Brand new unused$200

2000cc bosch injectors Brand new unused direct fit for RB26 matched set $800

Or the entire fuel system for $1400

Cams and springs Apexi Vmax 272 degree 11.2mm lift camshafts, These have done approx 6-7 race meetings and are in perfect condition. No marking or damage. Still installed in cylinder head sitting on the shelf.

Apexi V max springs to suit above cams

Apexi V max titanium spring retainers and collets

$1000 for the whole valve train

Clutch Excedy twin plate PULL type clutch. Done some work but has never been in anything other than my road GTR. Probably 70% life remaining, removed and ready to go

$500

R32 GTR intercooler perfect condition no dents or damage

$200

R34 front end conversion and wide body Never fitted or used. Full kit minus headlights. To suit R32.

$800

Wilwood pro lite calipers 6 piston, brand new never used or fitted. ill check piston sizes

$1000

Wilwood bias controller and master wilwood bias valve, 1 inch master cylinder with no proportioning valve. Braided teflon lines to suit. Suit brake upgrade with bias issues. Used but good condition

$300

Everything located in sydney.

Photos will come when I have time to upload them

Link to comment
https://www.sau.com.au/forums/topic/373302-rb26-parts/
Share on other sites

Thanks Charlie I thought they were 272's but there you go.

Cams are as Charlie mentioned 270x11.4mm

The wilwoods will take up to a 370x36mm rotor. I had them mocked up for a 360x36mm rotor which was going to be used on my GTiR project. Gone with smaller 16x10 wheels so they can't be used anymore though.

I'll put photos of the fuel system up latter today

Link to comment
https://www.sau.com.au/forums/topic/373302-rb26-parts/#findComment-5954685
Share on other sites

Injectors and one surge tank are sold.

I still have the fuel pump and a surge tank that was specifically designed to suit the pump and filter.

Has a block with 1/8th NPT threads cut for fittings and a male -12 AN fitting welded on at the right height for the pump to line up with.

post-20349-0-47074500-1312802729_thumb.jpg

post-20349-0-79527500-1312802847_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/373302-rb26-parts/#findComment-5956059
Share on other sites

  • 1 month later...
  • 10 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...