Jump to content
SAU Community

Recommended Posts

the R33 turbo has a steel compressor wheel

the r34 turbo has a plastic compressor wheel

they both have ceramic exhaust wheels

ive herd that some S2 R33 turbos have the plastic wheel aswell but im not sure.

but i think the plastic compressor wheel is better then the ceramic one from the R32s.

but i think alot of the gained power has been from the VVT. There's less lag aswell.

Well I guess it depends what limits rpm first, the valvetrain or the bits of metal swinging around underneath...

After hearing the Blitz R34 drifting car screaming on the (sounds like 8,000rpm+) limiter I am guessing that this is the difference.

an RB26 has the same size bore and a longer stroke and revs higher than an RB25 so...

Well I know it probably doesn't mean much cos I don't know what the R33's rev like but at 7000rpm mine absolutely sings. Haven't tried taking it higher though.

The turbos for the R33 and R34 bolt on exactly the same. I assume they have exact power comparisons. After my turbo blew I was looking at a rebuild but after alot of frigging around I just brought an R34 turbo yesterday and I get the car from the performance shop today. I will post in the next few days with any differences (if any) I notice with the new turbo and hopefully some dyno sheets to compare

Well I guess it depends what limits rpm first, the valvetrain or the bits of metal swinging around underneath...

After hearing the Blitz R34 drifting car screaming on the (sounds like 8,000rpm+) limiter I am guessing that this is the difference.

Hit the rev limiter on me GTT for a short time.. oops.. :| But friend of mine reckons its a very sweet sound.. :)

As to the original post.. not sure about the exact diff between the two turbos.. but was told that the standard R34 turbo can take 1bar normally no problem. Tho cant say I'm gamed to do it atm. :(

Hrmm.. 0.7 bar.. what does that read on the standard boost gauge? Think mine is running approx. that, on my boost gauge the needle goes over ~2/3mm after the indicater between the 0 and 1+ :) (On boost that is) The turbo seems fine, cause I usually drive with more than just a few squirts.. :(

Ppls,

Skylineboy: Titanium wheels? Yes, F1 turbos used to have these. Obvious advantages, and obscene costs.

I've raised my boost upto the factory boost cut point on my R34 (a touch below of course) and and have had zero problems thus far (* frantically knocking on wood *).

I bounce off the rev limiter quite often. The factory tacho in the dash just isn't fast enough and first gear often sees me hit the limiter. oh well, that's what its there for!!

BASS OUT

  • 8 months later...
the R33 turbo has a steel compressor wheel

the r34 turbo has a plastic compressor wheel

they both have ceramic exhaust wheels

ive herd that some S2 R33 turbos have the plastic wheel aswell but im not sure.

The S2 R33 GTS25t type-m has a turbo charger made by hitachi, and it's had a ceramic compressor wheel.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Had a go at the stuck crush tube this afternoon. Tried things like grips and a chain wrench first but wouldn't just twist straight off. So got to work with a drill. Started small and kept a depth stop on to make sure I didn't drill into the bolt. Made a line of drill holes all the way up and enlarged them. Then a combination of chisel and Dremel to split it all the way up. Levered the split to get oil in there and eventually it gave a bit while levering. Worked it back and forth with loads more oil till it was spinning freely, then with grips I could work it downwards and off. And no significant damage to the bolt (not by me anyway - just the 27 years of rust)
    • Well, I'm tired. I'm tired because about 4PM yesterday, before today's appointment someone immediately bought my bumper. They couldn't get it any other day as they're on the way back to NSW. So I had to do that big GTR conversion I had been planning. Unfortunately, the information on SAU about what you need and how this is done is incomplete. So what should be a simple bolt on affair, yeah, it's not. Did you know if you use all GTR items the bonnet won't close? This little manuever sent me into about 1am the night before trying to dodge a way to get it closed. I will have to revisit this in the next few days  - or maybe not, I may let a body shop figure it out. It all needs to come up and my motivation to pull the bumper off is low. It also seems to hit things in the bay where the GTT bonnet didn't. Yes I used 100% new OEM GTR items. Today, I had the joy of driving to the dyno looking like this: Given I had roughed in the fuel and given sensible but pretty conservative timing, I didn't really bet on having the car drive out any real difference than when it drove in. Sadly due to a miscommunication and laptop fun and games (and almost bricking the dongle, prayers and firmware updates indeed), I ended up using HP Tuner credits to licence the car that was already licenced. So in the end my laptop was used. It turns out my butt dyno is still well calibrated after all this time. The 325kw was on 74% Ethanol, the 313kw line was on 98. The other line is the 'before' line which was 281kw. While the numbers are pretty low, they're pretty in line with what you'd expect. Even if US dynos bump the whole result up about 50KW, gaining 10-15% is similar gains.  The curve of the cam is pretty much spot on with what was discussed as well. All this said, it still feels bad to not see the number you secretly want to see. Even if the car drove great beforehand, and I knew pretty confidently the car would drive out much the same way it drove in due to the nature of a wellish dialled in LS1 not gaining much if anything at all from being tuned from where it was. As expected, the car isn't particularly sensitive to running it at anywhere between 12.0 and 13.0 - And the initial timing at 20deg and 12.0 made 308KW. So 3 degrees of timing, and leaning it out to 12.7 for 5kw, anything above stopped giving any benefit until E85 (which has an additional 2 deg as before). Car itself behaved entirely fine. I found out that 100C = 1.15V! IAT at about 7pm was 19C. I might mess with the bonnet mounting.. but given the REO NEEDS TO BE CHOPPED TO FIT A GTR BAR this is possibly something I may leave gathering (more) dust until it returns to paint jail.
    • It sounds farrrrrrr too cold at your place Duncan... Here I was thinking our 10 degrees overnight is getting cold...
    • oh yeah, reminded this morning....bin lids frozen shut too
    • In my case not, because of total reno. But yeah.
×
×
  • Create New...