Jump to content
SAU Community

Engine Fan Replacement, Or Electric Thermo Fan

TWOAR81

By TWOAR81,
in Four Door Family & Wagoneers

 Share

Recommended Posts

TWOAR81 Collaborator

TWOAR81

Posted
Posted

Hi Guys,

just wondering how many of you have replaced the engine fan with a Thermo model instead. For a daily driver, wife to work and back... Me having some fun on weekends..

Did a search for Options and this looks like the go..... Any preferences opinion on this?

And if so ball park cost.....:thanks:

wolverine Grand Master

wolverine

Posted
Posted

The clutch fan is almost guaranteed never to overheat the car. There is drag on the engine but it is fairly idiot proof compared to some of the issues that can come with thermofans (from appropriate shrouding to decent thermostat control).

There are numerous threads in forced induction from memory on the pro's and con's.

wlspn Proficient

wlspn

Posted
Posted

To go against the trend a bit here I have a 16" Davies Craig & have never had overheating problems be it in heavy traffic, on the dyno, etc, etc

So many people on here (not saying the guys above) make it sound like it can't be done without issues but like anything, if done properly, it can...

wolverine Grand Master

wolverine

Posted
Posted

I hope my post didn't come across like it can't be done, it can. However you want to go in with your eyes open as there are potential issues.

I would love to remove the clutch fan for a reliable thermo but last time I looked (admittedly a while ago) I decided it would be cheaper and easier to go with another stock clutch fan.

What thermostat are you using wlspn?

Rekin Grand Master

Rekin

Posted
Posted

I hope my post didn't come across like it can't be done, it can. However you want to go in with your eyes open as there are potential issues.

I would love to remove the clutch fan for a reliable thermo but last time I looked (admittedly a while ago) I decided it would be cheaper and easier to go with another stock clutch fan.

What thermostat are you using wlspn?

Im using this to control my thermofans.

http://www.spalusa.com/store/Main.aspx?p=itemdetail&item=FAN-PWM-V3

slippylotion Mentor

slippylotion

Posted
Posted

On my 180sx I used ba falcon twin fans controlled with a greedy unit. It took temp reading from the factory ECU sensor. It controlled both low and high speeds of the fans and when aircon switched on. It lasted on there about 2 weeks before I replaced it with the clutch fan.

The temps always fluctuated within 10 deg where as the clutch fan keeps them within 3. The factory clutch fan is a heap more consistent and easier.

Daleo Grand Master

Daleo

Posted
Posted

I don't think there's a Thermo fan on the market that can push the amount of airflow a clutch fan is capable of pushing.

I've used thermo setups before, and eventually gone back to the old clutch style fan. Simple and effective.

TWOAR81 Collaborator

TWOAR81

Posted
  • Author
Posted

Yep, exactly what I thought easy and simple.

My 2009 ford ranger still uses it so... Why not.

@ 165 for a new one why not? Anyone had one of these go die?

Would love to know....!!!

wlspn Proficient

wlspn

Posted
Posted (edited)

I hope my post didn't come across like it can't be done, it can. However you want to go in with your eyes open as there are potential issues.

I would love to remove the clutch fan for a reliable thermo but last time I looked (admittedly a while ago) I decided it would be cheaper and easier to go with another stock clutch fan.

What thermostat are you using wlspn?

No, as I said in my post, that wasn't aimed at anyone in this thread or anyone in particular, have just seen guys on here stating that a thermo will always cause overheating, etc & it's stupid to use one.

Just wanted OP to realise it can be done but as you say there are things that can go wrong or be done wrong...

When I first fitted the thermo it was due to cooler piping & I preferred the idea of that rather than removing the standard shroud or trimming blades as some people do.

My cooler setup has now changed & I could run the clutch fan again but currently have no reason to as temps are very steady under all conditions...

Nothing wrong with the clutch fan. It does its job superbly & is basically idiot-proof.

Fan is controlled by my Haltech (through standard temp sensor) with an over-ride switch

Edited by wlspn

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • Kinkstaah
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Kinkstaah · Posted

      You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • Dose Pipe Sutututu
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Dose Pipe Sutututu · Posted

      LOL.... you are correct there.
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      It's been quite the ordeal but hey, at least you figured it out.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...