Jump to content
SAU Community

Recommended Posts

G'day Guys,

Mate of mine is looking for a company car, he reckons he will have about 25-30k mark. Doesnt mind second hand within reason.

He is however against falcons and commies. Likes his BMW's and what not. Doesnt want a hatch either.

I have tried to steer him away from second hand BMW's with near 100,000kms due to the after expenses (he works for his parents so we dont want to screw them around).

He likes the Cruze, any one have thoughts and opinions about them?

Recommendations?

Cheers,

Link to comment
https://www.sau.com.au/forums/topic/377132-new-car-for-30k/
Share on other sites

I have driven a Cruze before.

Decent car for getting from A to B.

Comfy, good on fuel and has quite a bit of room.

Tell him, it's no performance car, kinda sluggish even if you plant your foot down, but it's a daily so it should be fine.

I would assume any car from a Nissan Maxima / Toyota Camry / Honda Accord / Mazda 6 / Subaru Liberty, 4 door sedans would suite him just fine as well.

Link to comment
https://www.sau.com.au/forums/topic/377132-new-car-for-30k/#findComment-6014610
Share on other sites

With full BMW service history...

and within $30K...

E39 530i or 535i

E46 328Ci or 328i

I've had both of the underlined above without problems at all. Weakness is mainly sidetanks or some other water issue.

Since your friend is in NSW, use BMV Engineering (Caringbah) to scrutinise any potential beemers. Massimo knows his stuff and charges much less than a dealership.

On the north shore (Artarmon), see George at BMWise

Link to comment
https://www.sau.com.au/forums/topic/377132-new-car-for-30k/#findComment-6014948
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...