Jump to content
SAU Community

Recommended Posts

Just out of curiousity where/what would you change in the tune to stop AFM cars stalling when running with a atmo bov/no bov causing flutter. I know you can tune it out as VL turbos and R31 redtop rb20dets never came with bovs and fluttered from the factory without stalling.

I imagine the cause of the stalling is where it runs very rich just after throttle off, would simply pulling all fuel from ~400rpm fix the issue? So when it stumbles it doesn't add even more fuel causing it to stall? Have any tuners looked at the stock redtop tunes to see what is different? I personally run the stoc recirc valve but I'm curious what the difference is.

One thing I have noticed is the redtop rb20s have a strange cylinder sticking out the intake that leads to nothing. This is post AFM and looks a bit like a buffer, could this be what they used to stop the stalling issues? Eg it buffers the fluctuations in pressure in the intake causing less AFM voltage fluctuation?

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

That would be a resonant chamber - just for noise tuning, although they can have a little influence on total power (in NA engines) by affecting the resonances in the inlet tract. I wouldn't expect any such effect upstream of a turbo however.

I would think that playing with the timing at the low rev high(er) load cells would be needed as well as fiddling with the mixtures. Kinda depends on what load cells it's actually accessing when the stall occurs though, because you wouldn't want to have to butcher the tune in those cells if they also happened to be cells that were accessed during normal operation, which is entirely possible.

because you wouldn't want to have to butcher the tune in those cells if they also happened to be cells that were accessed during normal operation, which is entirely possible.

Totally agreed, mainly why I mentioned the 400rpm cells as these would never really be accessed apart from when starting or the engine is stalling.

If anyone does have stock redtop rb20 maps, would you be able to look at these areas to see if there is anything stand out that might have been done for this reason?

Is this just an rb20 thing as Ive had my rb25 tuned with atmo bov (it was easier to install that way, less plumbing less fab) and I have no stalling issues, tuner did say the bov was quite good at staying closed and zero leak at the wrong times...

If anyone does have stock redtop rb20 maps, would you be able to look at these areas to see if there is anything stand out that might have been done for this reason?

Got any p/n's for ECU that came with bovless vehicles? I can check maps in Nistune and post 'em here.

Apparently some BOV users accept this fact.

And still have that little shimmer of hope that a girl will hear it, strip naked, and dive into their car. (Hopefully before it coughs up a heap of black smoke and stalls)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Need to see other side of PCB in that area...ie; I don't see any thru-hole mounting, just soldered vias (smd zeners in SOT23 have 3 legs but only 2 are used, as reflected by PCB tracks)
    • 4 to 5 is fine. It will be slow, but that's better than blowing turbos. I don't have a PS pump idle up solenoid on my car, because... I think when we put the Neo in we retained my R32 lines. But.... From inspecton of the R34 vacuum hose diagram, you can see that the solenoid needs to be connected to the turbo inlet as source of clean air) and the plenum (as source of vacuum - which is the place for the air to flow to to cause the idle to increase). So 3 to 1 is VERY WRONG. 3 should go to either the turbo inlet, or the plenum. Follow the other hose from the PS solenoid and if it goes to the plenum, then your 3 goes to 2 2 would also serve as a bleed port for a boost solenoid.
    • Pull them out and pull more apart. You can't do shit with them still bolted to the floor of the car.
    • Yes it is. ZD1 is on the other side of the board. Where ZD1 is marked is clearly opposite a 2 pin device. Our 3 pin device here is not a ZD.
    • Alright, a little update on this... I called Fulcrum, who used to be the distributor in Australia. No Bueno, they don't service them anymore.  Called shock works, who don't service them but offered to dyno the shocks for performance, and suggested DNA in Sydney might service them.  Called DNA, who also do not service them and basically said they try to steer customers away from tein for this exact reason these days- there is just no support for them anymore apparently.  Both SW and DNA said they are a not necessarily a bad product, but they just don't service the brand or know anyone who does service the brand anymore.  So... I could keep calling around but at this point I think I'll probably just spring for the shockworks product, unless anyone here knows anything.  Cheers 🍻 
×
×
  • Create New...