Jump to content
SAU Community

Recommended Posts

Just out of curiousity where/what would you change in the tune to stop AFM cars stalling when running with a atmo bov/no bov causing flutter. I know you can tune it out as VL turbos and R31 redtop rb20dets never came with bovs and fluttered from the factory without stalling.

I imagine the cause of the stalling is where it runs very rich just after throttle off, would simply pulling all fuel from ~400rpm fix the issue? So when it stumbles it doesn't add even more fuel causing it to stall? Have any tuners looked at the stock redtop tunes to see what is different? I personally run the stoc recirc valve but I'm curious what the difference is.

One thing I have noticed is the redtop rb20s have a strange cylinder sticking out the intake that leads to nothing. This is post AFM and looks a bit like a buffer, could this be what they used to stop the stalling issues? Eg it buffers the fluctuations in pressure in the intake causing less AFM voltage fluctuation?

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

That would be a resonant chamber - just for noise tuning, although they can have a little influence on total power (in NA engines) by affecting the resonances in the inlet tract. I wouldn't expect any such effect upstream of a turbo however.

I would think that playing with the timing at the low rev high(er) load cells would be needed as well as fiddling with the mixtures. Kinda depends on what load cells it's actually accessing when the stall occurs though, because you wouldn't want to have to butcher the tune in those cells if they also happened to be cells that were accessed during normal operation, which is entirely possible.

because you wouldn't want to have to butcher the tune in those cells if they also happened to be cells that were accessed during normal operation, which is entirely possible.

Totally agreed, mainly why I mentioned the 400rpm cells as these would never really be accessed apart from when starting or the engine is stalling.

If anyone does have stock redtop rb20 maps, would you be able to look at these areas to see if there is anything stand out that might have been done for this reason?

Is this just an rb20 thing as Ive had my rb25 tuned with atmo bov (it was easier to install that way, less plumbing less fab) and I have no stalling issues, tuner did say the bov was quite good at staying closed and zero leak at the wrong times...

If anyone does have stock redtop rb20 maps, would you be able to look at these areas to see if there is anything stand out that might have been done for this reason?

Got any p/n's for ECU that came with bovless vehicles? I can check maps in Nistune and post 'em here.

Apparently some BOV users accept this fact.

And still have that little shimmer of hope that a girl will hear it, strip naked, and dive into their car. (Hopefully before it coughs up a heap of black smoke and stalls)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Based off what you’ve said here, I think I’ve figured out a good bit of what I’ve done wrong -  So on the line going from the PCV valve to carbon canister, there’s a T joint that is pretty much right next to that lower port - I hadn’t noticed that the hose in the diagram was curved to attach onto the carb, so I was putting that line for the lower port onto the PCV line / carbon canister line instead. I’m going to have a flick through the manual again tomorrow and should hopefully find a diagram that’ll show me where that T joint should be connected to. Timing also 100% needs to be sorted out as well, should be able to tackle that tomorrow as well. Definitely feel like I should be on the right track now though. 
    • The screw is for idle (pilot circuit) mixture adjustment. Else, I'm confused ~ the diagram shows 2 carby ports, and the intake manifold port, but you're suggesting the "2nd port on the back of the carb that isn’t mentioned in the diagrams" ...yet, both carby ports are shown...que?... ...in any event, that port should be connected, but if not (like it is now), it's unlikely to cause a backfire out the carby (it would introduce false air and give you a fast/lean idle) ...sounds more like timing issues/spark plug wire routing responsible for the backfiring.    
    • That's fair, I can see both points. I get enthusiastic when I see the FS section has a new post and want to see what interesting thing someone is selling. Then I get deflated it's a bump of a 10 year old post. Ha ha
    • Couple of litres of moonshine from his southern cousins would do it...
×
×
  • Create New...