Jump to content
SAU Community

Recommended Posts

Just out of curiousity where/what would you change in the tune to stop AFM cars stalling when running with a atmo bov/no bov causing flutter. I know you can tune it out as VL turbos and R31 redtop rb20dets never came with bovs and fluttered from the factory without stalling.

I imagine the cause of the stalling is where it runs very rich just after throttle off, would simply pulling all fuel from ~400rpm fix the issue? So when it stumbles it doesn't add even more fuel causing it to stall? Have any tuners looked at the stock redtop tunes to see what is different? I personally run the stoc recirc valve but I'm curious what the difference is.

One thing I have noticed is the redtop rb20s have a strange cylinder sticking out the intake that leads to nothing. This is post AFM and looks a bit like a buffer, could this be what they used to stop the stalling issues? Eg it buffers the fluctuations in pressure in the intake causing less AFM voltage fluctuation?

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

That would be a resonant chamber - just for noise tuning, although they can have a little influence on total power (in NA engines) by affecting the resonances in the inlet tract. I wouldn't expect any such effect upstream of a turbo however.

I would think that playing with the timing at the low rev high(er) load cells would be needed as well as fiddling with the mixtures. Kinda depends on what load cells it's actually accessing when the stall occurs though, because you wouldn't want to have to butcher the tune in those cells if they also happened to be cells that were accessed during normal operation, which is entirely possible.

because you wouldn't want to have to butcher the tune in those cells if they also happened to be cells that were accessed during normal operation, which is entirely possible.

Totally agreed, mainly why I mentioned the 400rpm cells as these would never really be accessed apart from when starting or the engine is stalling.

If anyone does have stock redtop rb20 maps, would you be able to look at these areas to see if there is anything stand out that might have been done for this reason?

Is this just an rb20 thing as Ive had my rb25 tuned with atmo bov (it was easier to install that way, less plumbing less fab) and I have no stalling issues, tuner did say the bov was quite good at staying closed and zero leak at the wrong times...

If anyone does have stock redtop rb20 maps, would you be able to look at these areas to see if there is anything stand out that might have been done for this reason?

Got any p/n's for ECU that came with bovless vehicles? I can check maps in Nistune and post 'em here.

Apparently some BOV users accept this fact.

And still have that little shimmer of hope that a girl will hear it, strip naked, and dive into their car. (Hopefully before it coughs up a heap of black smoke and stalls)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...