Jump to content
SAU Community

Recommended Posts

Rb30 bottom end for 300rwks....errr nup

simple Bolt on GT3076, injectors and Nistune...bam there is 300rwkws

As for 300+ being useless and people will die using standard brakes and coilovers....errrm...sure...if you say so

I know its hard to hear as a newbie to search, you just want to hear the answers. But the answer is it depends on so many different things about what you want out of the car, which you havent specified. The best way to understand this is to read through the different topics on this forum and get a good overall understanding. If I was going to drop $20k to modify a car I would be researching the crap out of it.

Important things which I was not aware of before owning a rwd skyline:

- Lag, being a small 2.5L engine if you go for any more than 250rwkw on 98 fuel then you will notice an increase in lag. This continues to increase as you go higher in power. Over 300rwkw and you wont be seeing full boost to after 4000rpm at best. That only leaves you with less than 3000rpm of useable power assuming the standard rev limiter. But since you are talking about building the engine you could potentially raise the rev limiter with the right engine mods and this could be ok

- Traction with a rwd, even the standard turbo with a few mods and tune can be hard to launch in 1st gear without heavily breaking traction (with standard type tyres). I have 280rwkw and it can break traction in second gear even with wide grippy tyres.

- Axle tramp, I experienced a fair bit of axle tramp (wheels bouncing up and down as you break and regain traction), to resolve this you need to address the suspension which can be tricky to work out what is causing it. Super stiff coilovers can make this worse.

- Fast, the other thing is how fast a skyline can be without huge power figures. They are a lighter car and dont need the huge power figures of an XR6 Turbo to be fast. My car with 280rwkw is very quick, I would expect to run high 11 second 1/4s with a good launch and is plenty for the street.

Have a good think about it all and do plenty of research. If your talking about dropping a tonne of cash then I would look at a GTR, that way it should hold its value better and you have some hope of getting big power to the ground.

Best of luck!

It's a spring loaded momentary switch. Press it once, that should turn TCS off (and light in the dash), press it again TCS on (light off).

Are you sure TCS is operating? (Can check this pretty easy comparison with TCS fuse removed) Have you checked to see if the TCS switch is plugged in? (People often unplug it when doing work under the dash) Does the TCS bulb in the dash light up when you turn the ignition on (but don't start)?

checked the switch its plugged in, the light comes on when the ignition is turned on but pressing the switch has no effect traction control is always on :-(

so does taking the tcs fuse out disable traction control?

Dont be too hard on him... he did own a 4 door r33 after all :ph34r:

Hiya timmy :action-smiley-069:

haha hey how are ya ;-) that was the mrs 33 got flamed for that when i put it on here too dunno why i bother sometimes lol

used to have a r31 wagon sleeper with a rb20det and microtech uleh but never put it on here could only imagine what people would say about its standard brakes lol

checked the switch its plugged in, the light comes on when the ignition is turned on but pressing the switch has no effect traction control is always on :-(

so does taking the tcs fuse out disable traction control?

What makes you think that traction control isn't being disabled? Can you drop the clutch in first and smoke it up?

But yeah just pull the fuse, it stops the module getting power.

Edited by Rolls

yer like i said wouldn't spin no matter what the switch did, pulled the TCS fuse now we can have some fun feels more responsive too

he's taking it up to mercury motorsport in a couple months for turbo fuel pump injectors ecu fmic exhaust and all the other mods to get it to around the 250rwkw mark

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...