Jump to content
SAU Community

Recommended Posts

It should do. although you need to make sure that all the flanges match. The GTT driveshafts are 5 bolt. I don't know about the GTV ones, but there are also 6 bolt (GTR) flanges and 6 bolt (which is really 3 pairs, as used on S chassis cars) and it is remotely possible that Nissan were licking cane toads when making the GTVs and used one of the other flange types. More likely that they just used the normal 5 bolt though.

Tailshaft flange should be the same. They'd need serious toad usage to change that.

The diff housing should just bolt up - they're all just R200 housings bolting to the same sort of subframe.

Should bolt straight up. GTt and GTv are the same.

Essentially a GTv is a non-turbo GTt.

On a side note:

If you change your diff ratio you might need to reconfigure your speedo.

The ABS (3 channel) system "might" need tweaking too as the ABS sensor monitors the speed of the each front wheel and the rear drive shaft, the system "could" potentially crap itself when ABS is kicks in, due to mismatch in sensor readings.

ABS does not need tweaking,

as long as the diff has the ABS sensor on the front side of the diff then you are sweet should bolt in straight up and off you go provided the halfshafts match the driveshafts on the car.

i went from a 4.11 diff to a 4.36, did not notice any change in speed however when in 5th gear, doing 100km it would sit higher revs (3200rpm or so compared to around 3000rpm or under with the old diff)

ABS does not need tweaking,

as long as the diff has the ABS sensor on the front side of the diff then you are sweet should bolt in straight up and off you go provided the halfshafts match the driveshafts on the car.

i went from a 4.11 diff to a 4.36, did not notice any change in speed however when in 5th gear, doing 100km it would sit higher revs (3200rpm or so compared to around 3000rpm or under with the old diff)

I was refering to actual road speed. ie. if your your speedo reads 100km/h, is your car's speed relative to the ground 100km/h.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My idle is set at 950rpm though - Moving the timing around 20 degrees is not really what I'd call a calm idle. That said... neither is chop, by definition. The LS ECU likes to adjust timing to hold idle as opposed to air. It'd work, but generally speaking there'd be a discrepancy in the base idle and the IACV would want to move the timing around anyway to maintain said idle. I think I'm just going to keep the timing steady anyway. Preserve my engine mounts.  My aircon is now officially regassed. As the guy was reversing I noticed my reverse lights do not operate, along with my reverse cam. This is a bit distressing, because 100% of guides talk about which wire to connect to backup cams as "the goes with the [other color] wire". Often when doing conversions. Unfortunately the R34 colour wires aren't documented Unfortunately I had a T56 Magnum gearbox with it's reverse switch, which also isn't documented. Unfortunately there's definitely not documentation for people with both of these in the one car. Unfortunately I forgot. After many hours of this, I have a reverse cam and reverse lights again. The wire going through the trans tunnel to the reverse switch had broken. Upon inspection, it looks like this one wire had about 7 spade terminals and extensions in it.. for reasons I cannot possibly comprehend. I also spent the 750 hours required to clean up the wiring behind my head unit which now looks like this: This is a monumental improvement relative to what used to be there WRT triple gauges, head unit, traction control, wideband controller, and whatever the f**k OEM stuff still exists there in various states of connectivity/needed. Next step is to check in at the Exhaust shop to see/confirm how much clearance I have, to decide what mid mufflers or 'resonators' (which are just straight through, narrower mufflers) I can add and hopefully cut out a lot of exhaust leaks, pinhole, v-band or otherwise. But first step will be to 'take a look' before the next step.
    • Fark the AFM card and Nistune, Haltech Nexus S3, DBW, cruise control, flex fuel, dis dat.  
    • It's most likely the bolt/bush where the cover bolts back wore and allowed cover to move forward.
    • Still haven't put the injectors and R35 AFM in so we can tune the bloody thing for the HG highflow it got mid last year! I think I can forecast the upgrade path to a bigger twin scroll, external gate, Haltech, flex setup, Samsonas, dis dat, etc will be .... a while away!
    • Should have taken that opportunity to slot in a twin scroll turbo setup. Maybe next time.
×
×
  • Create New...