Jump to content
SAU Community

Greedy Profec B Spec 2

KEBAB_DRIFTER

By KEBAB_DRIFTER ,
in Engines & Forced Induction

 Share

Recommended Posts

SargeRX8 Grand Master

SargeRX8

Posted
Posted

What is the one way valve you speak of? The Greddy boost controller kit comes with the control module, inline filter, a dual stage solenoid and other little bits and pieces. Ive been running mine like that for 2 years on 2 different cars without a problem. Greddy manual doesn't say anything about it either.

Beer Baron Grand Master

Beer Baron

Posted
Posted

yes they are filters and yes you should use one. stops crap getting into the solenoid. should really use one before the map sensor too (internal in the profec BII). so you need to buy 2 inline filters. try and get the genuine trust ones (I think it's trust that are the good ones). some are like 2 cheap discs that re just glued together. the proper ones have the two halves screw together and often seal with an o-ring. the cheap ones easily break apart and leak, the good ones don't. shouldn't be more than about $10-$15 each.

Beer Baron Grand Master

Beer Baron

Posted
Posted

where can you get them from Beer baron?

i tried to search b4 i installed my EBC nut seemed like noone stocked them.

I even rang CRD (greddy dealer for AUS) and they had no idea what it was :O

yeah no one carries them. I have wholesale accounts with most makers in japan so just buy 20 or so every know and then. have some stuff coming next week and I'll order some of each size (there's 2 sizes). if anyone wants some just pm me, i'll do them at cost. from memory the trust ones are good (screw together) and a bit cheaper than the HKS ones. they both make 4mm and 6mm size. generally you need one of each (6mm for solenoid and 4mm for map sensor/display unit).

krayzie32 Mentor

krayzie32

Posted
Posted

yeah no one carries them. I have wholesale accounts with most makers in japan so just buy 20 or so every know and then. have some stuff coming next week and I'll order some of each size (there's 2 sizes). if anyone wants some just pm me, i'll do them at cost. from memory the trust ones are good (screw together) and a bit cheaper than the HKS ones. they both make 4mm and 6mm size. generally you need one of each (6mm for solenoid and 4mm for map sensor/display unit).

Ill have 2 of each please.

Feel free to pm me :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The king 2.0
      Nissan fuga 450gt android screen

      By The king 2.0 · Posted

      Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • MBS206
      NC MX5

      By MBS206 · Posted

      My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • dbm7
      Automatic Power Button Light Flashing

      By dbm7 · Posted

      Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Duncan
      R34 Plug Identification

      By Duncan · Posted

      Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...