Jump to content
SAU Community

Recommended Posts

Its pretty dim in the garage.......looks so much better in natural light.....

20121121_115931.jpg

for some reason this picture didnt upload earlier.....

and thanks mate ^^^ ...this thread is getting loooong !! Bit boring though now because there has'nt been any real big stuff to report....lots of plans though in the near future...so my fingers and toes are crossed !!

So this morning while I was going through some performance imports mags I came across this.................................

IMG-20121201-WA0000.jpg

And I wanted to do something similar too.............so I went to the shops and could not find a black sweatband so went to red dot and bought three pairs of black socks (will use the other two pairs for work)...and began to do some "art and craft"............

20121201_105032.jpg

Result............

IMG-20121201-WA0002.jpg

And on the car................ :domokun:

20121201_114410.jpg

My attention has now been diverted to the engine bay...............and since I don't want to spend any big bucks at the moment.....I have been doing this...................

Boring old plastic washer bottle...............

20121207_155253.jpg

After the plastic primer and first coat of paint..............

Made sure to leave a strip so that I can actually see how much water is in there...going to look like this :ph34r: !! haha

20121207_160847.jpg

Will post completed pics when it dries and I put it back on............

Edited by jez NF

SEEN THESE WHEELS BEFORE ????!!!!..............look what I found them on while randomly on google searching for wallpapers !!!!!!

autumncarsphotographyjapanesetoyotatownvehiclessupercarstuningtoyotasuprasideviewjdm_wwwwall321com_88.jpg

In other news...the container is almost dry and looks yumm.....doing the coolant one now....

autumncarsphotographyjapanesetoyotatownvehiclessupercarstuningtoyotasuprasideviewjdm_wwwwall321com_88.jpg

DSCN1410.jpg

See what I mean.....................

....and update....I drove ALL THE WAY TO WORK with my phone stuck under the hood !!!! Silly me left it there this morning when I was rushing to refit the wiper washer water containter thingo before work.......it still "work"s as normal !!!

Edited by jez NF
  • 2 weeks later...

Did some detailing of the "bunky".........................and then I bought some high temp paint for my exhaust piping.

The front bar and half the bonnet has not yet been done in this picture...........it is surprising what a little bit of time, effort and average levels of detailing skill can achieve. I know this is a terrible picture and you probably cannot really tell any difference unless you look very carefully but a little bit of effort is all it took and man this thing is shining now !!

IMG-20121227-WA0004_zpse1950283.jpg

Then moved on to my car again...........

Tried to get the exhaust off....but when I realized that it was beyond me I decided to give it a shot and paint it on the car itself.......made sure I had newspaper ontop of it as I didnt want other bits to get sprayed too and sprayed the living hell out of it with degreaser first and just went in with the high temp black....could not be bothered with sanding down / prep and all that jazz...it cannot even be seen !!

This is as high as I can get the car at the moment (without axle stands)...so had to make do.

20121228_145615_zps9a73012c.jpg

Came up pretty well I thought judging by the general lack of attention to detail and half arsed effort...going to let it idle for a while and then turn off tmrw.....and then take it for a short run to and from work so hopefully the paint will cure and wont peel....intercooler piping is still perfect so hopefully it lives up to its reputation and wont too.

IMG-20121228-WA0003_zps87bad6f3.jpg

That is the weld mark from when "kermit" modified my exhaust so that it had less angle and didnt burn a hole through my rear bar.

OH and that looks SOOO much better than the rest of the exhaust at the moment !!

So...............pulled the sunshade thingo down the other morning when I couldnt see a thing because of the blooming glare and thought to myself.....there is a great discovery to be unraveled here..........hahahaa.....no I didnt...I thought.....man this is boring !!

Seeeeeeee what I mean...

20121230_194251_zpsd0d44584.jpg

So I pulled out some of the left over leather trim that I had..............

20121230_194310_zpsaadb3c0a.jpg

...and then I became F U N K Y ...........................lol

20130101_121402_zpscb50145a.jpg

Outside view

20130101_121745_zps241be496.jpg

BTW...Happy new year people :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...