Jump to content
SAU Community

Recommended Posts

Hey going to buy these rims, just wondering if anyone has them on there r32 gtst and how they went? or on any nissan without flared guards?

i have coilovers so can adjust them to whatever height it good for the rims, and rolled guards. planning on putting 235's on the rears and 225 on the front so they are streached quite a bit.

any pics of your cars? will 10'' be to wide or should i go with the 9.5's?

thanks

Link to comment
https://www.sau.com.au/forums/topic/377971-rota-gtr-d-rims-18x10-12/
Share on other sites

way too wide for a GTSt in 10", esp in that offset. you'd have clearance issues fo' sure

would make more sense to get a staggered set, in widths more suited to the tyre size

My mate had some on his 180 with standard guards . 10" gtc's with +5 offset and wasn't a drama , looked sick . Don't see why they wouldn't go good on a gtst

coupla points:

• from a performance perspective, fitting tyres that are far too narrow for the rim is just carrying extra weight and reducing clearance for no good reason. a manufacturer would be looking to fit at least a 285 tyre to a rim that wide from the factory

• they're so much wider than standard rims you'll need to have the car engineered to make 'em legal

of course, if you're one of these 'drift-look tyre-stretch' fashion slaves, or just like to tell people at the pub you've got 10 inch wide wheels- go nuts

coupla points:

• from a performance perspective, fitting tyres that are far too narrow for the rim is just carrying extra weight and reducing clearance for no good reason. a manufacturer would be looking to fit at least a 285 tyre to a rim that wide from the factory

• they're so much wider than standard rims you'll need to have the car engineered to make 'em legal

of course, if you're one of these 'drift-look tyre-stretch' fashion slaves, or just like to tell people at the pub you've got 10 inch wide wheels- go nuts

Thanks for the advise though mate, anyone else ?

You'll need to massage the guards to make them fit.

guards are rolled and flared a tiny bit, not much...do you guys have experience with it or are u just presuming?

i got 10.5'' deeeeeep dish on there now with +20 offset and don't even stick out that much...

I'm just presuming.

After seeing a friends 32 gtst with TE37 superlaps in 18x10.5 +15 with 265/35 A050s, he had to flare 50mm out so, depending on size of tyre you want, you may have to flare bit more

  • 4 months later...

I hav xt7 18X9.5 +12 on my 32 gtst. Cambered in and rolled front and rolled and flared rear. Looks mean man if you want to go for an aggressive staunch look. So i say go for gold, i got 215s on mine so do what u want wit tyres,. No one cares these day about whhats legal ay.

I'm just presuming.

After seeing a friends 32 gtst with TE37 superlaps in 18x10.5 +15 with 265/35 A050s, he had to flare 50mm out so, depending on size of tyre you want, you may have to flare bit more

russ's car is a different beast man... and he is running 265's

ok, so iv decided to buy some work XD9's .

Rear 18x10 + 18

Front 18x9 +20

look great, will see how they go :D

if you want xd9's look into running the 17x9.5+17 on the front and the 18x10+18 rear... best option by far

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Cheers. Skyline is back on the menu, can’t get rid of it. It’s like a child you don’t want, or herpes 
    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
×
×
  • Create New...