Jump to content
SAU Community

Recommended Posts

HI ALL I GOT A R32 GTR 1989. HAS A APEXI POWER FC Z32 MAFS, CAMS, COOLER, INJECTORS THE NOMRAL STUFF

JUST HAPPENED OUT OF NOWHERE WHEN TO DRIVE IT STARTED IT UP MOVED OUT OF DRIVEWAY WHENT TO TAKE OFF AND IT DIES IN THE ASS.

PUT IT IN THE GARAGE AND SAT THERE WILL REV BUT WITH HESITATING WHEN U PUT URE FOOT DOWN LIGHTLY AND HOLD IT THERE BUT WHEN U STAND ON IT IT JUST POPS AND FARTS AND BACKFIRES THROUGH THE INTAKE AND WONT GO OVER ABOOT 2-3,000

CHANGED FUEL PUMP AND HAS POWER AND ALL GOOD

CHANGED FUEL PUMP CONPUTER IN THE BOOT AND THE RELAY NOT THEM

MAFS ARE BOTH WORKING AS FAR AS A CAN SEE. TOOK TOPS OFF AND LOOK OK. BUT NOT 100% AS I HAVENT CHECKED THEM ON ANOTHER CAR OR VISEVERSA

NOT TOO SHURE ABOUT COMPUTER HAVENT GOT HAND CONTROLLER TO CHECK IT OR ANYTHING

INJECTORS AND COIL PACKS ARE GOOD.

CHANGED COILPACK WIRING NOT THAT.

CHANGED SPARK CONTROLER OR WHATEVER IT IS ON THE TOP OF THE COILPACK COVER NOT THAT

CHANGED EXHAUST CAM SENSOR NOT THAT

TURBOS ARE FINE.

PRETTY SHURE ALL THE HOSES AND ALL ARE STILL FINE.

HAS GOOD FUEL PRESSURE.

IT SEEMS TO REV A LIL BETTER WITH HIGHER FUEL PRESSURE BUT CANT FIND OUT WHY IT WOULD BE IT SITS AT AROUND WHAT IT SHOULD BE ACCORDING TO THE MANUAL MAYBE A LIL HIGHER.

IF ANYONE HAS ANY OTHER IDES OR CAN HELP ME OUT WITH MAYBE BORROWING A MAF SENSOR OR ANOTHER COMPUTER THAT HAS ABOUT THE SAME MODS SO I CAN DEFINATELY RULE THEM OUT THAT WOULD BE SUPER. AND COMPINSATED THROUGHT HE BEER ECCONOMY OF COURCE.

tested the volts on them and had mates computer in it with the hand controler and the volts when up on them but may still be the problem ill try get some known working ones to try

  • 3 weeks later...

all were wrong sort of.

found out by looking through the computer that all the settings for everything were set back to stock. computer has wiped and reset it self to the factory rb26 settings. so mafs were wrong injectors were at 100% and maps are wrong just needs a retune now.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah. OK. I'll say the same thing I say to everyone. You do not have to use 100% throttle all the time.
    • Mainly being afraid of breaking something on something i've poured so much money into haha
    • Hey   ive gone for a terminated harness on my build so selling brand new unused and unopened piggy back harness  https://www.haltech.com/product/ht-141357-elite-2000-2500-nissan-skyline-r32-33-r34-gt-r/ Located Bathurst NSW   price $600 + postage     
    • The trigger kit I have is similar to the one in the link below. While going through Facebook, I saw someone else mention a similar issue, and I’m starting to think this could be related to the crank gear itself. I understand these parts are CNC machined, but maybe some earlier versions or individual pieces might have slight inconsistencies—it just doesn’t look right in my case. https://www.facebook.com/share/16an8evZd9/?mibextid=wwXIfr I originally installed the crank gear using the thin OEM washer, but as shown in the attached photo, the timing belt walks very close to the edge. When I tried using a Nitto washer—which is thicker—it actually made the issue worse. The belt walks about 1mm off the front edge, which raises more concern about alignment.   I’ve gone through the full process of elimination:   The tensioner pulley and bolt are brand new and installed correctly. The bolt isn’t bent and is oriented properly. The back of the tensioner and the idler pulley are clean and seated correctly. The idler sits slightly more forward, which I understand is due to its design. I’ve experimented with both tight and loose belt tension, but it makes no difference. As soon as the engine runs, the belt immediately walks forward again—even if I reset it beforehand.     At this point, I’m considering replacing the crank gear with your Race Version 1 (12-tooth), but before purchasing, I wanted to ask:   Are you aware of any alignment issues when using this gear? Would this gear help keep the belt aligned correctly, or could the walking still occur? Does it work with a standard missing-tooth crank and rear washer? Is there any specific crank setup or install procedure required?     For reference, I’m not using a front washer, as the PRP crank gear seems to replace the need for one.   Looking forward to your advice.
×
×
  • Create New...