Jump to content
SAU Community

Recommended Posts

Mmmm 1300 bucks haha

U doin sump baffles, oil return/breather from the head Etc?

Dan is pretty much making all the decisions lol. I just told him what I want out of the car etc and he will work with what I want :)

I am not sure on what parts are going in just yet I know the basic stuff just waiting on the list to be sent through.

  • Replies 69
  • Created
  • Last Reply

Top Posters In This Topic

....and once I get the problem Ill post in here :)

yes please, in particular oil pump and big end bearing condition. My guess is still on clearance problems causing pressure loss under load.

Put it on the dyno and see if it still drops pressure, will narrow down if its the Gs or some other issue.

Did you ever try this? It will very quickly sort out if it is an assembly problem, or a sump design issue.

Edited by Rolls

yes please, in particular oil pump and big end bearing condition. My guess is still on clearance problems causing pressure loss under load.

I am sure Dan will post in here.

Did you ever try this? It will very quickly sort out if it is an assembly problem, or a sump design issue.

I personally filled the sump with 6l as its the standard sump it still did it, so I am guessing it is oil pump issue but yeah wait and see I guess.

I suggested putting it on the dyno lol, not overfilling it.

Yes however you also said sump design which is standard hahaa. No we did not put it on the Dyno. I am just playing the waiting game hahaa lol.

Yes however you also said sump design which is standard hahaa. No we did not put it on the Dyno. I am just playing the waiting game hahaa lol.

Yep the standard sump might not be sufficient for the Gs you are pulling is what I was getting at, hence put it on the dyno and it will very quickly tell you if it is an issue with the sump, or an issue with the build.

  • 2 weeks later...

So you never tried it on a dyno to determine if it was the oil pump or the Gs and stock sump?

: /

No we didn't, however some what glad we didn't. Found half a washer(looked like a washer) in the sump just floating about. If I would of upped it more and more I could have done more damage.

The crank so far looks good so there is no need to replace that yet.

I have gone by what Dan has said and he are still trying to diagnose the issue.

Pretty much what my number 6 looked like when it let go....

it had standard pistons running 285rwkw.

what generally causes the piston to break away like that... is it just cause they're weak? or is there other contributing factors?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Put a fuel pressure gauge on it. Replace the turbos. Probably completely separate issues.
    • What copper washer do you guys use on the bleeder bolts? The existing one I have I had no idea where to find it in a local store, I did buy some online but that are only 1mm thick whereas my old one is 2mm+ thick and when I put the new washer out and squeeze the top radiator hose I can hear a bit of air but not with the old one. Does this matter? The new one doesn't leak, but the inner diameter is a bit loose whereas the old one threads on the bolt.
    • Howdy all, after being out a few weeks ago on a spirited drive in my GTR I have 2 issues that oddly have appeared at the same time. Whilst accelerating quickly through the gears all of a sudden i’ve lost power at the top of third gear (below redline around 6000rpm) for no obvious reason.    From that point onwards the car has been running rich on idle, won’t really rev under load without a ton of black smoke and the odd backfire, and dying as a pull up to a set of lights unless I keep the revs up around 1500rpm. In addition when shutting down the car that same night (I was 10 minutes from home) I noticed one of the turbos was significantly noisy on wind down when shutting off the engine. After letting the car cool down overnight it starts up fine, although once it gets to temp the revs start to creep up and down, the exhaust is darker than it should be and it also sounds like it’s running rich (fat note) I’ve put a new set of plugs in it - no change, the old plugs all seemed OK with two of them being somewhat richer/fueled up than the other 3 with 1 being borderline. I’ve smoked tested the intake system via the front of the Turbos, found a split vacuum hose going to the factory boost gauge sender, which I have since replaced.  Also found another leak on the gasket coming off the rear turbo outlet, have also replaced this. After fixing both of these leaks - still have the running rich issue. I’ve also tried another pair of AFM’s - no change here After pulling off the front turbo intake pipes, there is obvious shaft play in the front turbo, which now hisses loudly on light revvs although I can’t see why this would make the car run funny even under idle. I’m curious to know why it’s running rich before I potentially replace/rebuild turbos. The car is completely stock <50,000kms  other than an exhaust. Oil and coolant are all clear. I haven’t bothered with coil packs as it looks like they won’t be the issue due to condition of the plugs. Any help appreciated as I cry myself to sleep!
    • No probs at all. I used to love trying to dig up obscure info for those in need where possible going back 20+ years on SAU.  I did have another look and couldn't come up with any closer match. I'm leaning towards those skirts in your first pic are custom fitments, cut down/extended or from another car entirely and modded to fit an R34 sedan. I would've thought someone in Japan had them and taken a photo at some stage over the last 2 decades but there's nothing. Someone out there must know surely.
×
×
  • Create New...