Jump to content
SAU Community

Recommended Posts

1994 R32 GTR, the car's had blitz blow off's going to atmo for a while, gone to reinstall the stock blow off, removed the blanking cap from the pipe to have a fair amount of oil come out, what's this mean? a blown turbo oil seal prehaps? pic of the pipe i'm talking about below.

view through the front bumper

BOV.jpg

with the bumper removed

BOV4pipe.jpg

the blitz blow off valves.

BOV3.jpg

You found oil in the dead end of the recirc line? That's the lowest point, I suppose it could find its way there whilst it was blocked off at the BOV end if it was still connected at the turbo inlet end, but it could be residual from when the recirc BOVs were still being used. What's a "fair amount" of oil? 1 tablespoon? A cupful?

There's always some oil in the intercooler plumbing - the cam cover breathers also connect into the turbo inlet and depending on how much your engine breathes, you'll have anything from a little to a lot of oil in there somewhere. A lot of oil is of course undesirable - for one it tends to suggest a lot of breathing which is a sign of wear, and it also tends to promote detonation because engine oil being breathed in with the air-fuel mix has a low detonation threshold.

Oil can of course enter the induction tract from leaky turbo seals. It can be hard to work out where it's coming from though.

If you've got enough oil being breathed in to cause you running problems, then you'd probably notice a reasonable amount of oil usage across a service interval.

called previous owner, he say's he's been running the blitz BOV for around a year which would explain the build up of oil, no air flow through the pipe meaning no way to get rid of it, also explains the oil leak onto the front bumper, reinstalled the stock blow off valves and plumbed them back in, solved my over fueling issue and leaking oil issue, oil's green because the previous owner used martini oil's, which are green.

Edited by ttoks

If you want to do the right thing by your car, you need to pull off the intercooler, return pipe and all the intake hoses and give them a good clean.

Flush the intercooler with petrol until you can shake about 200ml of petrol in there and have it poor out clean. Same with the return pipe.

Most important of all, invest in a catch can that actually works or you will be cleaning it all again in a few months.

Flush the intercooler with petrol until you can shake about 200ml of petrol in there and have it poor out clean. Same with the return pipe.

Best cleaning methond is a 50/50% mix of Methylated Spirits & Kerosene.

:thumbsup:

Please tell me you had the motor and car properly inspected before purchase?

Just cleaning the pipes would be the end point. For safety sake get a comp/leak down test done.

Especially given the price it was selling at - perhaps you've just found the reason why it was cheap.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...