Jump to content
SAU Community

Recommended Posts

  • Replies 48
  • Created
  • Last Reply

Top Posters In This Topic

could end badly

the attessa is sensitive enough to play up with worn rear tyres, so running a staggered offset you's have to get tyres that are really close in rolling circumference/diameter

offsets would probably be ok, is it for an auto or manual? i forget now

its a manual, and after using a rolling diameter calculator, icame up wiht the following.

these are the wheels combos.

19x9.5 +11 with a 275/30 tyre, overall diameter = 647.44 mm

19x8.5 +11 with a 235/35 tyre, overall diameter = 646.93 mm

so they are quite close, if i sit down im sure i can work out some difference in pressure to bring it even closer together.... the attessa isnt that sensitive is it haha... 1.49mm difference.

YES IT IS THAT SENSITIVE. YOU ARE NOT LISTENING. Having a slight flat tyre is enough to set off the attessa, just but wheels in IDENTICAL sizes. It's not a hard concept.

Actually no. Just ignore my post again. I want you to f**k your car, maybe then you will listen.

so to get this correct in my head for when i finally buy a decent set of rims. buying rims that are different widths (ie 8.5 and 9) with different width and sidewall height (ie 235/40 and 265/40,35 or watever) will f**k it up but if i get both as for example 19 inch by 9 inch with 245/40 tyres but have the fronts as +22 offset and rears as +11 offset won't. Ignoring the fact that i've pulled these numbers out of...well you know where as far as if they will fit in the guards. The fact that the only difference is the offset means they will work....yes? because the only difference is how far the outside of the rim sits from the hub?

sigh, dont post if you have onthing imformative to say

the reason im asking questions is because i need answers, otherwise, my car would have the wrong wheels by now, there no need to be a wanker. i understand the rolling diameter issue, thats fine, i just want to see how sensitive it is. now whats wrong with changing the tyres.... couldnt i just run 245's all round, im pretty sure u can go down to 235 on a 9.5 inch rim??? so a 245 should be fine, but it would be stretched on the 9.5 so again would that change the rolling diameter???

how are there others running staggered offsets?? ive seen other stages with it done.

Edited by OMY31T

so to get this correct in my head for when i finally buy a decent set of rims. buying rims that are different widths (ie 8.5 and 9) with different width and sidewall height (ie 235/40 and 265/40,35 or watever) will f**k it up but if i get both as for example 19 inch by 9 inch with 245/40 tyres but have the fronts as +22 offset and rears as +11 offset won't. Ignoring the fact that i've pulled these numbers out of...well you know where as far as if they will fit in the guards. The fact that the only difference is the offset means they will work....yes? because the only difference is how far the outside of the rim sits from the hub?

thats correct, you can run different offsets, but not a different overall rolling outer tyre diameter. the problem ive got is finding somthing unique in my budget that suits the car

Off sets don't matter, just rolling diameter, I have 18x8 with +35 fronts and +6 rears on my rs4s, I didn't realize that the manual needs same offset front and rear and the auto needs staggered offsets when I bought my rims. I'm putting 30mm spacers on my front rims when I get the time.

f**k it, i decided to buy some KOYA Endless rims. 19x8.5 and they are blanks so i can choose the offset i want. $290 a rim with whateva offset i desire.

so, to make it simple, what offset should i run all round on 19x 9.5's on a RS4S to have the wheels sit just under the guards in the rear without pumping the guards. i will most likely buy 245x35's all round for the rubber.

lol im sick of hunting, its easier to get somthing made.

ok no wories, i hope ur right hahaha.... otherwise i will be wasting over a grand :P

going off a calculator this is what ive come up with

from the stock 6 spokes which are a 7" +30 offset

with a 19x8.5 at +6 offset

i will have and extra 5mm clearance on the inner side

and have a the wheels 43mm wider on the outside.

that sounds right, because as u could see in the original pics, that the wheels sit in quite a bit. so 43mm should bring them basically inline with the guards. but im just wondering if i should go a bit higher in offset to be on the safe sifde because i dont want to get them and not beable to lower the car, and i will more than likely put in some adjustable camber items to fix up bad camber from lowering, so i think i might go a +11, because i know for a cact i have 5mm extra on the inside of the wheels from where they fit now, so the inside will be sitting the same and the outside will be 38mm wider, whcih should give me a few mm of clearance for camber correction.

Edited by OMY31T

i wouldnt go +6, u will almost certainly have clearance issues once lowered. anywhere between +10 and +15 would be the go. ive got 18x8.5+23 on mine and they could use a 5mm spacer, but im not gonna use 1 cos its illegal.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...