Jump to content
SAU Community

Legality Of Front Fenders

ausdrift

By ausdrift,
in General Maintenance

 Share

Recommended Posts

Zorro Community Regular

Zorro

Posted
Posted

Say what?

Fiberglass replacement part/panel is what FRP stands for

lol ---> FRP meaning! :)

Most kit cars & some manufacturers cars are made from frp or carbon, kevlar and a few other alternate materials. So im sure it would be possible to get them engineered if need be.

I had frp panels all over one of my cars for several years, bonnet, boot, 1/4s, aprons etc, never had a problem with it. Probably no-one ever noticed, being painted?!

Triptych Proficient

Triptych

Posted
Posted

The supplier of Fibreglass bonnets with ADR approval is Blits Bodykits in QLD. I am unsure if there approval carries over to other states or not as I am unsure on how the whole process works.

The website is http://www.blitsbodykits.com.au/

zebra Grand Master

zebra

Posted
Posted

lol ---> FRP meaning! :)

Most kit cars & some manufacturers cars are made from frp or carbon, kevlar and a few other alternate materials. So im sure it would be possible to get them engineered if need be.

problem is when you change from steel to FRP or even aluminium (GTR guards etc) it changes the "crash worthyness" of the car, hence making it un-roadworthy.

It sucks because front guards are not structural, but in the even of a prang fibreglass/carbon splinters will spray everywhere, even more so if you hit a pedestrian.

If you have the budget to crash test all your panels (like blits did) i.e crash your car into a wall a few times then you can produce adr approved stuff.

I'd be dubious if an engineer will touch stuff like that, but it may be possible given enough cash.

In saying that I had a Carbon bonnet on the R33 for years an never got picked up on it.

mad082 Grand Master

mad082

Posted
Posted

lol ---> FRP meaning! :)

Most kit cars & some manufacturers cars are made from frp or carbon, kevlar and a few other alternate materials. So im sure it would be possible to get them engineered if need be.

I had frp panels all over one of my cars for several years, bonnet, boot, 1/4s, aprons etc, never had a problem with it. Probably no-one ever noticed, being painted?!

completely different rules apply for kit cars to mass production cars. same with hot rods when run on limited rego

StevenCJR31 Veteran

StevenCJR31

Posted
Posted

Say what?

Fiberglass replacement part/panel is what FRP stands for

And no not legal in either state

wikipedia says FRP stands for fibreglass reinforced plastic . . . BUT in this context means something else

Triptych Proficient

Triptych

Posted
Posted

BRISBANE , i thought so = NO RULES

Just a quick quote from the blits website.

"BLITS is the first Australian company in Australia to manufacture street legal fibreglass bonnets, that made for federal regulation transport approval Australia wide".

So it would appear they are approved for use in all states and not just QLD.

BLITZ-26 Mentor

BLITZ-26

Posted
Posted

called RTA no problem with fiberglass guards .... then called an engeineer here no problem went over the pits with mine 30mm fiberglass front and rear guards passed no worries words stated to me by the inspector " i have no problem with these as they dont fall under any ADR restrictions" ? he also had no problem with my bonnet pins?

anyway not sure in melbourne but call and ask if you can or not?

The Bogan Grand Master

The Bogan

Posted
Posted

2.7.1 Strength and Thickness

The thickness, of non-intrusion panels, with gel coat removed, must be at least 3.5mm.

Bonnets and guards are examples of non-intrusion panels

The strength and thickness of structural components such as floorpans and bodies that

incorporate seatbelt anchorages, door hinges and latches etc., must be certified by a signatory.

The fixings for replacement fibreglass panels should have the same positions and must have at

least the same strength as the fixings used for the original panels. A combination of steel and

neoprene washers of a minimum 20mm diameter should be used with all fixings.

Seat and seatbelt anchorages, door hinges and latches must only be affixed to fibreglass

panels, floorpans or bodies that have been reinforced to take the loads such components are

capable of generating both in normal use and in a crash.

4.3.2 Fibreglass and Other Composite Replacement Panels

Original bolt-on metal bonnets and mudguards for pre 1971 (ADR 10) vehicles may be replaced

with fibreglass or other composite panels that comply with sub-section 2.7, providing the

modification does not increase the rigidity of the front structure of the vehicle and the

collapsibility of the steering column on ADR 10 vehicle is not compromised.

The catches and/or the design of the replacement bonnet must prevent it from being propelled

through the windscreen into the cabin area in the event of a frontal collision.

http://www.infrastructure.gov.au/roads/vehicle_regulation/bulletin/pdf/NCOP6_Section_LH_Body_and_Chassis_01Jan2011_v3.pdf

http://www.infrastructure.gov.au/roads/vehicle_regulation/bulletin/vsb_ncop.aspx

Links kindly supplied by Zebra

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By GTSBoy · Posted

      I don't think the shuffle can damage the turbos. It only happens at low shaft speeds and loads. It's just annoying (to some people - others are tickled by the effect) and it quite possibly reduces spool performance a little bit.
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Oh dear. The panel beating needs to be done before the filler work. Do you have a photo of the dent before you started? Hard enough to not flex and only hit the high spots?  What do you mean it was just temporary? 
    • Manur33
      Vag Coil Diy loom wire guage selection

      By Manur33 · Posted

      Can u check this way it works for power supply?
    • Manur33
      Vag Coil Diy loom wire guage selection

      By Manur33 · Posted

      These coils draw 10amps that what i read online
    • nouveau_poor
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By nouveau_poor · Posted

      I appreciate the detailed explanation, think I understand now. I spent the better part of last night reading what I could about shuffle and potential solutions. I had replaced the OEM twin turbo pipe with an alternate Y pipe that is separated further away from the turbo. The current one is from HKS and I had a previous pipe that was separated even further away, both have shuffle. I had heard that a divider can be welded in to the OEM pipe to remove turbulence, and figure that aftermarket pipes that are more separated would achieve the same thing. From what I read, most people with -10 turbos get shuffle due to their size, though it's a bit less common with -5s on a standard RB26. I think Nismoid mentioned somewhere it's because OEM recirculation piping is common in Australia with -5 cars. It seems that the recommendation tends to vary between a few options, which I've ordered in what I think is most feasible for me:  1. Retune the MAP or boost controller to try to eliminate shuffle 2. Install OEM recirculation piping 3. Something called a 'balance pipe' welded onto the exhaust manifolds. I don't know if kits for this are available, seems like pure fabrication work 4. simply go single turbo My current layout is as follows: Garrett 2860 -5s HKS Racing Suction intake MAF delete pipes HKS racing chamber intake piping hard intercooler piping,  ARC intercooler HKS SSQV BOV and pipe Haltech 2500 elite ECU and boost solenoid/controller HPI dump pipes OEM exhaust manifolds HKS VCAM step 1 and supporting head modifications Built 2.6 bottom end All OEM recirculation piping was removed, relevant areas sealed off I'll keep an eye out for any alternative solutions but can get started with this.  Only other question is, does shuffle harm the turbo (or anything else)? It seems like some people say your turbo shafts will explode because of the opposing forces after a while and others say they just live with it and adjust their pedal foot accordingly. 
×
×
  • Create New...