Jump to content
SAU Community

Recommended Posts

Hi guys;

So long story short, I thought i blew my turbo up - turns out the sound was my power steering or something (still not sure, taking it to the mechanic next week). Went through ALOT of hassle to put on an rb25 turbo and then cranked the car up to find out the noise that I suspected was the turbo was still there LOL! I actually thought the wheels were touching the housing etc which was all in my frikkin head. Mechanic had a look at my turbo after and said the amount of vertical shaft play is 100% perfect for a bush bearing turbo - ZERO horizontal movement and wheels spin free as anything. So here I am now :P (good for a laugh i guess).

I wanted a better low end response rather then power and I never actually got the car tuned or did anything after i put this on - just lazy.

So its up for grabs - has done around 30,000 km's or so. I paid somewhere around a grand for it, Hypergear can confirm I guess - but thats besides the point, I would like $450 for the lot which I think is pretty reasonable (feel free to correct me if I'm wrong). Feel 100% free to come inspect the turbo before you buy it as I'm not a pro and you shouldn't take my word for it - wasn't smoking, no leaks visible anywhere, blades are fine, came off a running car yadda yadda.

Comes with everything pictured (I might have a few clamps etc i can throw in). I can ship it interstate for $30 also. I'm located in Box Hill.

Let me know what you think - this should work really well on an rb25 (or anything when you spend time and tune the bloody thing :P)

dsc4002g.th.jpg

dsc4003i.th.jpg

dsc4004d.th.jpg

dsc4006.th.jpg

dsc4007.th.jpg

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/384138-tr43-turbo-and-accesories/
Share on other sites

Just in case its unclear - here's whats included

- Turbo (no dump pipe)

- 2x silicon joiners

- Braided oil line

- Actuator with hose

- Aluminium intake elbow

- rubber bend (one of the intercooler joins i think)

Items came off an Rb20.

hey mate, is it a 1st or 2nd gen tr43?

I just found out yesterday after someone sent me a PM that there were generation in this, if you tell me how to identify it I can tell you? Pretty sure Stao stopped doing these turbo's shortly after I bought this one ...

thanks mate - yea people have made some decent figures with supporting mods - that was why I got it in the first place. Never got around to tuning it and running some high boost through it =/

thanks mate - yea people have made some decent figures with supporting mods - that was why I got it in the first place. Never got around to tuning it and running some high boost through it =/

lol yeah got those figures without a tune, just bolted it on, chucked it on the dyno, up the boost and just made sure everything was running right.

noticed in the pic there is no actuator or flap, need to supply our own?.. also wondering if you know what profile it is as im after the g3 .82 profile..

perhaps u could email stao with a serial no on the centre cartridge to find out?

if you like PM me and we can sort these out and if all is well ill take it.

ATR43G3 .82 FNT wasn't invented till 2x years after this turbo was built. This is a TR43G1 does not blong to any ATR series, and retired. Its good for upto 250rwkws on a Rb25det with ok response.

r33230kw.JPG

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...