Jump to content
SAU Community

Recommended Posts

recently finished my build and went in for a tune. asked the mechanic to boost it to 17 psi as Ive been told by mates in the know" she be right"

old mate mechanic only tuned it up to 14psi not recommending going any higher unless i really want to lol

ok ive done:

PWR FMIC

Sard 555cc injectors

Nismo fuel pump

Apexi PFC

Z32 AFM

Spit Fire Coils

Tomei Pon cams

Custom Hiflow turbo (zorst side larger)

Blitz EBC

Ive got stock internals stock head gasket and i ran 235rwkw as 14psi. can i run 17psi with what i got?

Thanks David

Link to comment
https://www.sau.com.au/forums/topic/385018-boosting-a-r33-with-stock-internals/
Share on other sites

Depends what this "custom high flow" turbo is?

eBay specia?

haha not a ebay special. a mate of a mate worked for garret and done up 10 with dump pipe as a side project. ball bearing rated to 500hp

i got the last one and all feedback has been positive.

Just be careful. Fitting a 500hp cartridge to bored out stock housings never ends as well as expected.

Tune to to about 18psi but only within detonation and inlet air temp limits.

It's hard to say where the efficiency is in an unknown bastardized turbo.

There isn't really a set number, its more like how high does your tuner want to go with it. A mates R33 was on 1.5Bar for a good 4 years without a problem, only blew when he turned it up to 2bar without retuning it or anything lol.

Mines tuned for 17psi. Has been like that for a few months now, and had a good beating at the track where it was getting up to 1.4bar briefly too.

Lithiums R33 was tuned for 17-18psi for over 100,000km, and not many of them were nana km either.

Its all in the tune :) Rather than go be a KW queen, settle for a lower number with safer ignition if you cant afford/dont want to rebuild/replace.

I gave mine 1.45bar in winter and 1.3bar in summer all year round no dramas, didn't see anything go pop.. A/Fs were 12 and dipping to 11.5 at MBT and back up to 12 towards redline. A few people have seen how I drive my car too, driven like Nissan intended it to be driven.

  • Like 1

As stated the boost level isnt your limiting factor, its where your turbo runs out of puff (so to speak).

There will come a point where the turbo is simply pumping hot air and it will mean a bad tune ETC. With the right turbo theres nothing to stop you putting over 20psi into the stock motor, even that is nothing special.

this is a very valid topic and i think there are a lot of myths out there

and a lot of people get caught up on i want xxx rwkw and i have to run xyz psi

there is no magic limit or safe level for an engine for boost

why? because boost is simply the amount of resistance, nothing more

the less boost you can run the better

the more boost you run, the more stress and less efficient it becomes

the old hat method is keep winding in boost until you peak torque, airtemp doesnt ramp and you continue gaining power

ie why run 22psi when you stop making power/torque with anything past 16psi?

the point is

your tuner should dictate this type of value and tune as best he or she can within the turbochargers limits

exhaust back pressure is also a big concern so why run more boost if its of no gain

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...