Jump to content
SAU Community

Recommended Posts

Hey guys

So I got a Greddy Profec 2 for Christmas off the partner and its proving to be a pain to setup.

I ended up tapping into the vac line that the stock gauge uses (dont know if this is an issue)

Right now it seems to not want to go over 6psi

If anyone knows anything about these then let me know.

Settings I currently have it set to.

SET: 35%

GAIN: 5%

SET GAIN (start boost): 7psi

WARNING: 11psi

LIMITER: 5%

I think there might be a vac leak because when I pull the line off the nipple on the intercooling piping that goes to the solinode and the VAC on my gauge does not change a bit.

On idle sites around probably 20 or so

This makes me think there is already a big enough vac leak that by me doing this does not cause any issues

Here is a picture of what my VAC looks like when coming off throttle. (very bad)

1zf0xfb.jpg

Scrarching my head - so u connected it to the boost gauge sensor? Or the stock boost solenoid near the turbo?

U need to run it from the cooler pipe to the NEW boost controller solenoid then to the wastegate.

Then T into a vacuum/boost source such as the stock boost gauge sensor on firewall and run that one into the cabin into the boost controller

Haha nah sorry

The controller is hooked up to the actuator and the nipple on the cooler piping. All correct.

But my gauge sits at around -20 VAC

When I pull the line off the intercooler piping the VAC does not change is that normal? Or should the vac drop because it's got now an exposed nipple on the intercooler piping?

It also sounds like a sewing machine on boost which leads me to believe its defiantly got a leak somewhere.

But one question as well is for the boost gauge part of the profec I pulled the hose off from the stock vacuume line where it enters the air intake and ran a hose straight to my profec. Is that okay to do?

Can u post up a pic of the vacuum line ur talking about?

The cooler pipe line is before the throttle body so it wint really affect ur gauge reading after the throttle body. If that makes sense?

What do u mean by a sewing machine?

Try upping the gain to 15, set the boost warning to 15psi.

Watch the boost gauge and see if it holds flat or if it oscillates up and down

I will take a pic tomorrow of the vac line it comes out of the back of the intake manifold and normally goes to the stock gauge inside the car. Instead I pulled it off and ran my own pipe from it to my gauge in the car

Just has a sewing machine noise hard to describe but as it spools it has a noise like a sewing machine lol

My phone network is down so I cant get pics.

Right now I fiddled with the setup and the T now goes into the fuel regulator VAC line

I put the stock gauge VAC line back onto the back of the intake manifold.

Anyone know of a simple technique to find a VAC leak?

I tried spraying the hoses with "start ya bastered" to see if I could hear a change in revs but I cant find it

When coming off WOT the gauge shows -30 VAC and the Greddy unti shows -99 VAC

Both of which are the lowest numbers they can display

I think there might be a vac leak because when I pull the line off the nipple on the intercooling piping that goes to the solinode and the VAC on my gauge does not change a bit.

. It won't, I believe this part is under mild pressure at idle. Pull a vac line off after the throttle plate and see if the idle changes.
Just has a sewing machine noise hard to describe but as it spools it has a noise like a sewing machine lol
u sure it's not just the boost controller solenoid clicking away, they can be pretty loud.

I pull hoses off and it does not really change so the VAC at -30 is pretty normal?

I think I had it the wrong way around I was thinking your vac went lower when you had a VAC leak.

So if I had a leak I would expect the number to increas to say -20?

the ticking might be the solenoid then I guess because I have never had one I always used the boost T.

yes its normal to drop lower when you come off WOT, -30 in that case would be fine

you really need to show us how its been hooked up from where to where.

have you tried upping the boost or what? make sure you have the solenoid hooked up right too in terms of in and out

I wish I could get a photo but as I said I am with vodafone so nothing is working haha

The car is running great though.

Boost is tuned for 8psi and 10psi for 2 settings.

It all seems to be running fine now guys

When I get back from the coast I will post up some pictures

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...