Jump to content
SAU Community

Setting Up My Christmas Greddy Profec

Manuel Kasko

By Manuel Kasko,
in Engines & Forced Induction

 Share

Recommended Posts

Manuel Kasko Grand Master

Manuel Kasko

Posted
Posted

Hey guys

So I got a Greddy Profec 2 for Christmas off the partner and its proving to be a pain to setup.

I ended up tapping into the vac line that the stock gauge uses (dont know if this is an issue)

Right now it seems to not want to go over 6psi

If anyone knows anything about these then let me know.

Settings I currently have it set to.

SET: 35%

GAIN: 5%

SET GAIN (start boost): 7psi

WARNING: 11psi

LIMITER: 5%

I think there might be a vac leak because when I pull the line off the nipple on the intercooling piping that goes to the solinode and the VAC on my gauge does not change a bit.

On idle sites around probably 20 or so

This makes me think there is already a big enough vac leak that by me doing this does not cause any issues

Here is a picture of what my VAC looks like when coming off throttle. (very bad)

1zf0xfb.jpg

DVS JEZ Grand Master

DVS JEZ

Posted
Posted

Scrarching my head - so u connected it to the boost gauge sensor? Or the stock boost solenoid near the turbo?

U need to run it from the cooler pipe to the NEW boost controller solenoid then to the wastegate.

Then T into a vacuum/boost source such as the stock boost gauge sensor on firewall and run that one into the cabin into the boost controller

Manuel Kasko Grand Master

Manuel Kasko

Posted
  • Author
Posted

Haha nah sorry

The controller is hooked up to the actuator and the nipple on the cooler piping. All correct.

But my gauge sits at around -20 VAC

When I pull the line off the intercooler piping the VAC does not change is that normal? Or should the vac drop because it's got now an exposed nipple on the intercooler piping?

It also sounds like a sewing machine on boost which leads me to believe its defiantly got a leak somewhere.

But one question as well is for the boost gauge part of the profec I pulled the hose off from the stock vacuume line where it enters the air intake and ran a hose straight to my profec. Is that okay to do?

DVS JEZ Grand Master

DVS JEZ

Posted
Posted

Can u post up a pic of the vacuum line ur talking about?

The cooler pipe line is before the throttle body so it wint really affect ur gauge reading after the throttle body. If that makes sense?

What do u mean by a sewing machine?

Try upping the gain to 15, set the boost warning to 15psi.

Watch the boost gauge and see if it holds flat or if it oscillates up and down

Manuel Kasko Grand Master

Manuel Kasko

Posted
  • Author
Posted

I will take a pic tomorrow of the vac line it comes out of the back of the intake manifold and normally goes to the stock gauge inside the car. Instead I pulled it off and ran my own pipe from it to my gauge in the car

Just has a sewing machine noise hard to describe but as it spools it has a noise like a sewing machine lol

Manuel Kasko Grand Master

Manuel Kasko

Posted
  • Author
Posted

My phone network is down so I cant get pics.

Right now I fiddled with the setup and the T now goes into the fuel regulator VAC line

I put the stock gauge VAC line back onto the back of the intake manifold.

Anyone know of a simple technique to find a VAC leak?

I tried spraying the hoses with "start ya bastered" to see if I could hear a change in revs but I cant find it

When coming off WOT the gauge shows -30 VAC and the Greddy unti shows -99 VAC

Both of which are the lowest numbers they can display

hardsteppa Grand Master

hardsteppa

Posted
Posted
I think there might be a vac leak because when I pull the line off the nipple on the intercooling piping that goes to the solinode and the VAC on my gauge does not change a bit.

. It won't, I believe this part is under mild pressure at idle. Pull a vac line off after the throttle plate and see if the idle changes.
Just has a sewing machine noise hard to describe but as it spools it has a noise like a sewing machine lol
u sure it's not just the boost controller solenoid clicking away, they can be pretty loud.
Manuel Kasko Grand Master

Manuel Kasko

Posted
  • Author
Posted

I pull hoses off and it does not really change so the VAC at -30 is pretty normal?

I think I had it the wrong way around I was thinking your vac went lower when you had a VAC leak.

So if I had a leak I would expect the number to increas to say -20?

the ticking might be the solenoid then I guess because I have never had one I always used the boost T.

GTScotT Grand Master

GTScotT

Posted
Posted

yes its normal to drop lower when you come off WOT, -30 in that case would be fine

you really need to show us how its been hooked up from where to where.

have you tried upping the boost or what? make sure you have the solenoid hooked up right too in terms of in and out

Manuel Kasko Grand Master

Manuel Kasko

Posted
  • Author
Posted

I wish I could get a photo but as I said I am with vodafone so nothing is working haha

The car is running great though.

Boost is tuned for 8psi and 10psi for 2 settings.

It all seems to be running fine now guys

When I get back from the coast I will post up some pictures

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • pacman_1219
      Blue/grey smoke after idle

      By pacman_1219 · Posted

      Even with the piston at TDC there was room for it to drop, but I don't think it can drop fully into the cylinder, the problem you have is that you need something pushing against the valve to hold it up so you have enough room to put the new stem seal on and the spring etc.  I used compressed air only because putting rope in the cylinder seemed a bit risky to me, I know people have done it countless times before like this. Overall it's a pain in the ass job. Honestly you'd probably be better off taking the head off because the risk of dropping something in the engine and the finicky-ness of it all is very stressful. If you are going to attempt it though i 10000% recommend a 36050 valve spring/keeper tool. I had both the traditional lever type and after doing 1 cylinder it was absolute pain to get those valve keepers in place, even with 2 people. That 36050 is amazing, you do have to push hard to get them in place but it works perfectly almost every time. Back to my actual issue I think my engine is just tired and old and the rings have gone bad. The comp numbers (cold, no oil) were: Cyl 1 -129psi Cyl 2 - 133psi Cyl 3 - 138psi Cyl 4 - 137psi Cyl 5 - 157psi Cyl 6 - 142psi   Cylinder 5 and 6 having the most carbon on them.
    • MBS206
      R33 Fuel Pump & Brakes after alarm swap

      By MBS206 · Posted

      Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
×
×
  • Create New...