Jump to content
SAU Community

Towing A Car On A Trailer

AngryRB

By AngryRB,
in General Maintenance

 Share

Recommended Posts

AngryRB Grand Master

AngryRB

Posted
Posted

May sound like a silly question,

I'll be towing my car on a car trailer for the first time next week and need some advice on how to tie the car down, eg. where do i tie down? the diff? each wheel? all 4 wheels? chains or truck tie down ok?

Link to comment
https://www.sau.com.au/forums/topic/386869-towing-a-car-on-a-trailer/
Share on other sites
mad082 Grand Master

mad082

Posted
Posted

where you tie it down sort of depends on the trailer and where the points are to tie it down. my opinion is to tie it down via parts of the car connected to the lower part of the suspension that aren't going to move too much if the suspension is compressed. for example, if you were to tie it down via the body somewhere, if you hit a big bump then the suspension of the car can compress and the chains/tie-downs can slacken and the car can move. but as i said, it comes down to where the points are on the trailer to tie down to.

also make sure that you have the car foward all the way so you have most of the weight over the front of the trailer. this will make it tow better. having too much weight over the back of the trailer is a good way to cause an accident once you pick up a bit of speed.

AngryRB Grand Master

AngryRB

Posted
  • Author
Posted

Thanks for the tips, im hoping that 4 ratchet tiedowns ( 1500kg rated each ) is enough around the lower suspension on each corner then, i think the tow trucks use chains and winches but ill be driving steady , its a 30min drive and the front of the trailer has a wire that hooks onto the tow hook, and the trailer has brakes . The trailer says its rated at 1200kg, do you guys see any problem if the skyline is 1400kg?

Do you guys think there is any issues with this setup? i know i could of just got a tow truck but it would be alot more expensive.

benm Grand Master

benm

Posted
Posted

Think of the car as a tennis ball, doesn't matter which way you tilt the trailer (forward, backward, side) the tennis ball should not be able to move. Don't take any notice of how a tow truck operater secures a vehicle, 98% of them should be shot for their unsafe practices (a winch + 1 wheel tied down is not safe).

The easiest way is as Rekin has posted, using each wheel diagonally to the corner of the trailer. This prevents forward, backward and side movement but can play havoc on alignments.

Use 'hooker & keeper' 50mm ratchets which you can get a 4 pack from bunnings for about $50 rated to 1-2 ton. The amount of retards I see at motorsport events use 1x 20mm s-hook looped through the front axle and another looped through the back axle is astonishing. Most importantly is to tie it all down, then do a lap of the trailer to re-check each point then drive the car 50 or 100m and brake then get out and check it all again.

kawasakirider Grand Master

kawasakirider

Posted
Posted

Just make sure your hand brake is on and the car is in the gear that you value the least. Chuck a mate in there to hold the brakes on and turn the wheel for a bit of extra friction for security.

Make sure it can't move by tying it on as said (I'd also have the winch tightened if you can) and then take it a bit easy, towing a trailer with a car on it isn't hard if you use your brain, let people overtake you and if the trailer gets unsettled don't smash your brakes, pump them once and power out.

AngryRB Grand Master

AngryRB

Posted
  • Author
Posted

Thanks guys for all the good advice,

Towed the car to ERD this morning, ended up using 3 tie downs and had my bro follow behind me in his car just to make sure it was ok, first time towing was a bit anxious lol, but was suprisingly smooth ride,

the car didnt move at all on the trailer and was solid, the EL falcon got a work out.. i can see why people use 4wd's to tow there drag cars.. the temp guage was sitting high and the brakes became shakey by the end.

Cheers :thumbsup:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...