Jump to content
SAU Community

Recommended Posts

It’s time for me to part ways with this car. I’ve owned this car since it first came into the country in 2005. Car came over with 25,000 kms on the clock and now has 60,000 kms. The car has been looked after relatively well over its life (except when I blew up the engine), and now has a fully built RB30DET making 380 rwkw. Car has heaps of mods and I’ve spent way too much on the thing. Body is a bit rough, but there is no structural damage.

Car is still registered, never been defected

Is a regretful sale, have really enjoyed this car over the years, but unfortunately I don't have the time to drive it much anymore, and should be putting the money into the home loan instead.

Engine

RB30DET making 380rwkw @ 1.4bar (hub dyno)

R32 RB25DE head + RB30 block (lowered around 30mm, <5000 kms)

Trust T67-25G turbo kit (manifold to dump, including ext gate)

CP forged pistons 8.2:1

Argo I-beam rods

ACL Race series big end beaings

ACL Race series main bearings

HKS 264 x 8.5mm cams

Performance Springs valve springs

Adjustable cam gears

GTR oil pump (<2000kms)

Crank collar fitted

External head oil drain

Head oil feed restrictors fitted

Autronic SM4 (MAP sensor)

FMIC

3” exhaust, HKS super dragger muffler

Oil cooler + relocation kit

Blitz DSBC boost controller

Cooler sprayer kit (controlled by Autronic)

Bosch 044

1L surge tank

Driveline

Exedy 3 puck race clutch

RB25 gearbox + GTR shifter (shorter)

1 piece tailshaft

Kaaz 2-way clutch

3.7 final drive (was undriveable with the 4.3...)

Wheels / Suspension / Brakes

17x9 + 20 Buddyclub P1 all round

235/45R17 Kumho KU36 all round

Bilstein coilovers & Eibach springs (height adjustable only)

UAS adjustable front upper control arms (<2000kms)

Tien adjustable castor rods

R33 front LCAs (not fitted)

Rack spacers

HICAS removed

D-project adjustable rear upper arms

Whiteline camber kit in traction rod

Ally subframe bushes

27 / 24 mm Whiteline swaybars (not fitted, front doesn’t fit with lowered engine and standard mounts)

Caliper extension brackets for 324mm front rotors

RDA 324mm slotted front rotors (<1000kms)

Project Mu club racer pads (<1000kms)

Body & Interior

Genuine GTR front bar + N1 slots

Genuine GTR bonnet

Genuine GTR rear wing

Genuine Type M side skirts

Bride fixed back bucket (pretty knackered, not fitted, needs new rails, good enough for Mallala though)

Chasing $15,000 ono for it because of the amount of money I have poured into the thing.

Happy to answer any questions about it.

Can be contacted by phone / PM.

0422 255 843

post-21548-0-46948500-1326258247_thumb.jpg

post-21548-0-30957800-1326258254_thumb.jpg

post-21548-0-76974900-1326258267_thumb.jpg

post-21548-0-80641600-1326258277_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/387902-rb30det-r32-4dr/
Share on other sites

  • 2 weeks later...

Roy, nah the cams went in when I had the thing built, so no comparisons... Hopefully finds someone that can drive it more than I have latey!

Rolls, cheers. Have definitely spent too much money on the thing... The engine package alone cost me more than I'm asking for the car... :(

Link to comment
https://www.sau.com.au/forums/topic/387902-rb30det-r32-4dr/#findComment-6214232
Share on other sites

  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...