Jump to content
SAU Community

Recommended Posts

, and a few things falling into place the next 24hrs will play a big role in whether i bother with my current engine, or start with a blank canvas.

Roy, the clinic just called. They've approved your application for "the operation". Have you asked Prank to change your nic to "Royette"?

  • Replies 285
  • Created
  • Last Reply

Top Posters In This Topic

I have swapped by RB20DET in cam for an RB20DE.

You need to get the timing belt off, which is real simple and explained on the forum and in the GTR manual in the forum, making sure that everything is at top dead centre which is easy coz there are markings on the timing comers and on the rear timing cover (behind the cam gears). When taking of the harmonic balancer you will need a 27mm (I think socket). FYI – it is a normal thread.

Take the cam cover off.

Take the cam gears off.

Take the rear timing cover off (the cover behind the cam gears).

Very gradually undo the bolts that hold the bridges that hold the cam gear down. Do this slowly and take your time. When I did it I got some crud caught in the brackets which made it very difficult to undo the bolts - I though that I had threaded the holes but it was all ok.

You will notice that the bridges are numbered. They go from one to seven (I think) front to back. There are also little bumps in them that tell you which is the right hand side. Clean them up and take a look before you take them off - remember not to get excited and rush it.

Once the cam is out you can put the new one in. You might like to get a new front seal as the old one may be a little stretched. I think I paid $30 each (one for each cam) from Nissan who had them in stock.

I had a problem whereby the crud in the bridges made the screws stuck in there and I could not turn them. Using a vice and a hold punch I managed to get them out.

Remember to crew the cam in gradually when putting it back in. When I did mine I used the torque settings in the GTR manual which saw me snap one of the bolts. Once I got it back out again I simply screwed them down tight.

Put it back together ensuring everything is at top dead centre.

FYI the exhaust cam has a little something extra in the end of it which drives the crank angle sensor which the in cam does not have (this will help you to identify it if you mix them up).

I have tried to be brief. If you would like me to describe something in more detail let me know. Also look on the forum for the GTR manual. It has pictures.

Roy, you said doing it with the head on holds a few more challanges... why do you think so?

I would have thought taking the head off would be more difficult as you have more things to take off and be more careful with.

Only bonus is you can change your gasket, maybe do some porting and check out the condition of your pistons(not that youll see all that much... )

Dont have to, just thought i would, std springs are fine, my valvetrain is getting a little long in the tooth, so though some fresh valvesprings will help when i wind 1.4bar into the old girl (There she blows!)

My uinderstanding is the valves themselves will fall into the combustion chamber if you remove the valvesprings and associated valvetrain.

Dont have to, just thought i would, std springs are fine, my valvetrain is getting a little long in the tooth, so though some fresh valvesprings will help when i wind 1.4bar into the old girl (There she blows!)

My uinderstanding is the valves themselves will fall into the combustion chamber if you remove the valvesprings and associated valvetrain.

i wouldnt take your springs off without takin your head off, unless your pretty good. and puttin the collets back in would be fun with the head on, as you wouldnt be able to hold the valve up

It's the thicker white mark. If you are unsure, there are also timing marks on the cam gears and rear timing case cover. You can use them instead of the marks on the crank pulley.

I don't think that I would be able to do the job with-out removing the radiator.

Hey Waz,

Not alot happening at this stage as i had to fork out for new brake rotors just yesterday and decided to get some DBA 4000. very nice i might add, but this means the cam and cam/gear purchase has been put on hold. hopefully i will get around to it in the next week or two.

has anyone else started yet?

i managed to download the R32 GTR manual in PDF form, excellent help, i have printed out the relevant pages. it doesnt look like a difficult job, just alot of crap needs removing in order to get to the camshafts. what sux is having to drain the radiator and pull it out. its a fiddly job to do at home, looks like it will take a whole saturday to do properly

Roy,

You said you were looking at valve springs.

You wouldn't have a price on them would u? just off the top of your head.

I'm going to do valve springs to suit the cams later downt he track. BUT the price for a set of valve springs I got was up around the $700 mark.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...