Jump to content
SAU Community

Recommended Posts

yeah i tried all that Ben and Joel,

I just took it around the block then and it drives ok, feels a bit sluggish down low but starts to go hard by about 4000rpm, but i dont want to take it to high RPM or drive it too much just incase... but i drives, but will not hold idle.

  • Replies 285
  • Created
  • Last Reply

Top Posters In This Topic

HEY bbenny

just a thought but in the process of taking it all apart you may have accidently disconnected 1 or a few vacuum hoses...i know when i was mucking around puting in a catch can i knocked a vacuum hose and it did the same thing...idle would drop then die....similar to when you have a stock RB20DET and disconnect the plumb back pipe from the BOV

just a thought..maybe check all ther hoses

Aaron

yeah i tried all that Ben and Joel,  

I just took it around the block then and it drives ok, feels a bit sluggish down low but starts to go hard by about 4000rpm, but i dont want to take it to high RPM or drive it too much just incase... but i drives, but will not hold idle.

Wierd?? sounds like a vacum leak, or something like that. Is your vacum lines hooked up to your BOV? Might pay to get a timing light and check the timing??

Does it blow alot of black smoke out of the exhaust at idle? That is a sure sign of a vacum leak.........

i played with the idle, but no adjustments made any difference.

i did pull the throttle body off for the installation but i dont think that would be the cause.

It runs fine when you give it some throttle.

the only thing i see responsible is the stiff in. cam...

i have tried just about everything else there is!

i played with the idle, but no adjustments made any difference.

i did pull the throttle body off for the installation but i dont think that would be the cause.

It runs fine when you give it some throttle.

the only thing i see responsible is the stiff in. cam...

i have tried just about everything else there is!

does seem odd, thats why I thought of the throttle, maybe its not open enough under idle or something? could explain why its running fine when the throttle is open a little? just a thought, as other wise I have no idea mate, sorry

You checked base timing yet? what is that set to?

I can't really see how a cam that is harder to turn (but is also is just as hard when the stock cam is in place) would be the culprit

well it was noticably harder to turn...

but then again that could be due to some of the lobes compressing a valve or two...

I can only point to a few possibilities - either the in. cam is not turning free enough, as we have discussed.

or the posibility that the timing belt jumped a tooth when i started the engine

however i did turn the engine manualy 3 revolutions and check the timing marks on crank and cam pulleys...

Its frustrating!

I will disasemble the whole damn thing again and see if i find anything.

Yep i think it is.

Ive decided to bail on the cams as i just cant afford aftermarket management.

otherwise it would be one kick-ass upgrade, i mean 25rwkw average increase for $300 is pretty damn impressive!

so im a little dissapointed i cant pull it off with the std ecu

i can confirm it is the ECU flysky. because i checked and tried everything, there were no other causes.

and SydneyKid has done several running a PFC with no problems and considerable gains.

no probs with standard cams joel

Cams and cam gears are in... only thing is i need someone i Melb that has a blown RB20 that i can steal some parts off.

I need the cap for cylinder no.6 on the inlet cam...as one of the stud has siezed in the aluminium cap, i was lucky to get it unbolted from the head without snapping or seizing...

Anyone in Melb able to help me out, or know of a friend/workshop that can help me without woth one (will need thw two stude that go with it as well.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...