Jump to content
SAU Community

R33: Rear Seat Removal

jnr_j

By jnr_j,
in Tutorials / DIY / FAQ

 Share

Recommended Posts

jnr_j Community Regular

jnr_j

Posted
Posted

Skyline R33 Rear Seat Removal Pictorial Guide

You should see something like this with an obvious bolt on either side just below the base:

RSR1.jpg

Do this to both sides:

RSR2.jpg

The next step is the only tricky part. You have to pull the base of the seat up and out first, and on either side there is a metal loop stuck in a plastic type catch to hold the seat in place. One side at a time, you'll need to pull pretty much straight up around the area shown in red below. (The catch you're trying to prise free is seen below in blue). This can be hard to remove, in my experience you have to pull quite hard. You can push the middle seatbelt and buckles through the seat first to make things easier.

RSR3.jpg

You should now see something like this. Removal of the backrest is straightforward, just remove the bolt/screw on either side, slide the seatbelts on either side out of the way and then lift upwards and forwards.

RSR4.jpg

You just need to lift over the three hooks shown in red below. Remember to sit the backrest back up on these supports when you put things back in place.

RSR5.jpg

The quality back seats look something like this!

RSR6.jpg

http://users.tpg.com.au/johnkg/skyline/rea...eats/index.html

John

Link to comment
https://www.sau.com.au/forums/topic/39133-r33-rear-seat-removal/
Share on other sites
tridentt150v Grand Master

tridentt150v

Posted
Posted

Good thing, except that on my '98 R33 there are two 'prongs' that go through the floorpan and are released underneath the car by undoing a clamp and squeezing the 'prongs' together then pushing them back up through the hole. These 'prongs' are accessed from under the car ie they are outside the car. I haven't done it yet, tried to get my rear seat out but put the base out in the too hard basket. I only wanted to get my backrest part out anyway, and with a bit of patience it came without the need to take the base out.

PS you can actually see the holes for the 'prongs' in your photo, you have circled them in blue.

ferni Grand Master

ferni

Posted
Posted

Very nice guide!!

I pulled as hard as i could to get the seats out after i undid the bolts... no luck

so i managed (akwardly) to undo the bolts on back part of the seat without taking the bottom part out - was a biatch tho

Duncan Grand Master

Duncan

Posted
Posted
Good thing, except that on my '98 R33 there are two 'prongs' that go through the floorpan and are released underneath the car by undoing a clamp and squeezing the 'prongs' together then pushing them back up through the hole.  These 'prongs' are accessed from under the car ie they are outside the car.  I haven't done it yet, tried to get my rear seat out but put the base out in the too hard basket.  I only wanted to get my backrest part out anyway, and with a bit of patience it came without the need to take the base out.

PS you can actually see the holes for the 'prongs' in your photo, you have circled them in blue.

hey tridentt150v, I'm pretty sure the prongs you are talking about is the white plastic bit right? Thats just the mount that holds the metal prongs in the car body - the white plasticy bit should stay in the car and the metal loop bit is what you have to lever out.

  • 3 months later...
r33skylinegtst Mentor

r33skylinegtst

Posted
Posted

Um... i tried to remove my seats today and where you've circled the clips in blue in the third pic...well mine didn't come out quite right on the left side... the platic base that holds the clip also came out... is that bad? :s

51jay Mentor

51jay

Posted
Posted
Um... i tried to remove my seats today and where you've circled the clips in blue in the third pic...well mine didn't come out quite right on the left side... the platic base that holds the clip also came out... is that bad? :s

Hmmmm! Sounds like you've just written off your car....tough eh!!

On further consideration..you might just save the day if you prise the white base off the steel loop and replace it in the hole with a bit of silicon and an abject apology :wassup:

A better way to remove the seat base...especially if its tight ..is to use a large screwdriver or prybar just inside of the black bracket and lever it up

r33skylinegtst Mentor

r33skylinegtst

Posted
Posted

thanks 51jay but i meant from a safety point of view. :) sounds like no biggy. Still, couldn't get the seats out so thought screw it and gave up. Will do it later when i have an urgent need to. I only really wanted to get at the base of the back windscreen cause the guy who removed the tint did a crappy job and left glue all over the window.

  • 11 months later...
  • 2 weeks later...
r_speedfreak_r Proficient

r_speedfreak_r

Posted
Posted

Hey nice guide. I've tried taking out the rear seats previously along with a few of my mates and we failed. We got stuck at the same point everyone else seems to, but now i know it will eventually come out ill have another go at it. I think ill just get some leverage or muscle power and lift the front of the seat up until something breaks or it comes out lol.

  • 1 month later...
Murry33 Experienced

Murry33

Posted
Posted (edited)

FOR EVERYONE:

Even easier than pulling it up by yourself and taking a while and all that strength....... is to jam a crowbar under each side and pull up, its out in two seconds!......trust me it's easier hehe

Edited by NeesaanGTS
  • 11 months later...
RANDY Veteran

RANDY

Posted
Posted

Don't need piccies!

Bottom of rear seat has two bolts, on the side of the footwells, can't miss them)

Push the bottom-seat down around the seatbelt area, and you'll see a bolt on each side holding the back-seat in. Undo those.

Back-seat goes up to unhook, bottom seat goes forwards and up (it's hooked to the back-seat)

  • 4 months later...
  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • AnimalGarage
      spot the stagea

      By AnimalGarage · Posted

      It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...