Jump to content
SAU Community

Recommended Posts

hey guys,

took my car to get fuel in the morning yesterday, then washed it. ready for heathcote drag day. we left for the hume highway at 7.30, the car got to the servo fine where we met up with the rest of the cars attending. when we left i started the car all was ok, was travelling down the highway at 100Kmph, then all of a sudden felt the car not shaking but more like a shutter sort of like when you are about to stall it in a manual but all the time...when i accelerated the car would go nowhere untill the turbo kicked in then it JUST dragged the car along...we stopped at a safway on the side of the road, and i turned the car off and back on, and it still done it...i looked under the bonnet and everything seemed ok....i als checked for boost leaks using my gauge, and vaccum and boost was fine...i then turned the car off, left it for a bout 5 mins and turned it back on and it was FINE??!! i still didnt trust it so i left it there all day and went to the drags without it. i came back later that afternoon to grab it and it started fine, drive 50 mins home fine and now runs fine...i cant fault it now??

the car also sort of missfires when i put the foot to the floor at 5000 rpm, but the revvs still keep climbing like normal??? i changed the coilpacks and that helped a LOT, but it still does it under full throttle...its not like a missfire but like a stutter??

can anyone help with BOTH these problems???

cheers!

Link to comment
https://www.sau.com.au/forums/topic/391524-car-playing-funny-buggers/
Share on other sites

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

Id point towards a plug or sensor got wet or the fuel you got had some crap in it. seen as the only 2 things you did was wash it and put fuel in it. it might clear itself up after a drive, don't flog it to much in the mean time

In the boot, remove the back board, you will see 4 10mm screws holding down a plate. Remove that. Under there is a black lid thing with 3 hoses. You want to unplug the wires and get a rag ready for when you remove those lines as fuel is going to come out. Keep the hoses out of the way and take that lid off. To do that get a piece of wood and put it in the notches in the lid and tap it with a hammer to loosen it and get it out. Fuel pump is inside. Plenty of guides here to elaborate and show pictures of how to do it, wire it and fit it back in.

Its not a fun job. Don't do it on a hot day and be ready for swearing. DO NOT EVER attempt to do it with more than a quarter fuel in the tank. Hell run it to near empty if you can.

Fuel pump isn't that hard if you get a good one. my tomei pump was easy as. pull the old one out, drop the new one in

This. Took me half an hour, including diagnosis of why the car wouldn't start when I reversed the polarities :P

Agree with running the tank near empty first though. Arms get real damn itchy immersed in petrol ermm.gif

Edited by Hanaldo

This. Took me half an hour, including diagnosis of why the car wouldn't start when I reversed the polarities :P

Agree with running the tank near empty first though. Arms get real damn itchy immersed in petrol ermm.gif

And in a hot day, that itch plus the humidity rising from the fuel tank is enough to really f**king frustrate you when you cant get that cradle in the bracket.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...