Jump to content
SAU Community

Recommended Posts

Hey guys. Only have this build up on a small qld based forum, but i think this will be much more appreciated here, and seem to be able to get help alot easier :D

So i'll just start from the start and just copy, paste all my previous posts over, so bear with the epic first post :nyaanyaa:

Names daniel, recently off my p plates, so decided to get something boosted and rwd. Had a EG civic and was going to k swap it but decided i'd get something 4 door and finish the civic off properly and start again on it someday, maybe never if i like nissan too much haha.

Bought it off a guy on SD, thought it was going to be pretty straight forward as the wiring for the microtec had been done by TOP RPM on the coast. Wasnt so as a member off superglory found when he came to help with my gearbox wiring, the body loom has been molested and needs some time spent on it :(

Motor was out of the car when i got it and with no gearbox as he sold it for his sr box in his 180.

Hopefully get it on the road soon, still needs alot done, but i'll get there one day soon.

It started life as a genuine jap cab, plated as having a ca18i in it. parts list below

Car: 89' C33 Laurel

Engine Bay:

s1 Rb25det

Rb25det gearbox

Microtec lt12s

Turbo back exhaust w/ cat and twin kick up muffler

ASI performace r33 alloy rad w/ twin thermos

PWR intercooler, meant for evo but was 1 tube too high, snagged it cheap when i worked for pwr a few years back

Suspension: Tein HR Coilovers

My Mods: Work equip 01's (were meant for the civic) 15 x 9.5 +42 and 15 x 8.5 +52, need to order 30mm bolt ons to clear the 8.5s :\

Kazama rear camber arms

KTS rear toe arms

Roof wing (thanks to erin at jdm garage for the arms and whipping out a roof wing when i asked about one and making me buy it -___-

More to come...

As for how its going the list of things i need to do is extensive but i'd rather put it here cause it makes me feeel like i achieved something if i write it down

Motor and gearbox in

Dash trim back together

Radiator hoses

Engine loom connected

Install 5 stud, camber/toe arms

Find some s13 brake lines that run from booster along firewall to replace dodgy job old owner did

Navara speedo body mod

Mount intercooler

Intercooler piping made up

2x 90deg bends for piping to be fully done

intake arm, and pod filter, and mounted bracket for legalness

Reo back in

Front bar cut to fit and installed

Mount Radiator

Rad hoses on

INstall brake booster and master

Brake lines

Install Clutch master, hard line and braided line

Throttle cable in

Speedo sender in

tailshaft in

pop rivet Ally/checker plate where piping comes through bay, new neater holes

Get custom handbrake lines made

Install Gearstick boot/seal

Entire Rewire

Tune

Replace windscreen (cracked when i bought it), remove rust where windscreen meets roof

rego

Pictures to come Of empty bay and bay with motor in

IMG_0153.jpg

IMG_0155.jpg

And 9.5's on...needs less camber

IMG_0146.jpg

Also a pic of the new parts

93e2de62.jpg

So finally got somewhere with this thing.

Motor was already out from my place, De-greased and pressure washed the bay

IMG_0446.jpg

Then scotch brited it to get it nice and rough so the paint would stick

IMG_0456.jpg

got the front end up on stands, removed the subframe and sprayed it black, didn't come out nice and glossy so wet and dried it back to prep for the final colour

IMG_0464.jpg

The paint in question

IMG_0466.jpg

The end result. Not bad for a backyard job

IMG_0467.jpg

Sexy matching Rocker and cam covers

IMG_0475.jpg

New turbo setup some of you may recognize this :P gators gonna gate :D

IMG_0472.jpg

Motor and box back in, turbo setup bolted in place.

IMG_0474.jpg

Thats all the photos i have but the suspension is back in, front triangle bits in, castor rods back on. Just gonna work at it an hour or so after work every day, get brake booster, clutch master throttle cable in, then mate my catback to the dump pipe, tailshaft in and get this baby off to be wired!!

And a shot of all the rigs. We're trying to corner the market of nissan 4 doors :P

IMG_0477.jpg

Little update again slowly getting there, picked up a cheap padded nardi with bosskit through streeter.

ffd93a03.jpg

Got my silicone bends to finish the piping, now all i need is to make a stainless intake.

IMG_0524.jpg

and a shot of the front, with intercooler

IMG_0525.jpg

Little update, fitted my steering spacer. Had so much play in it, new one fitted there's no play whatsoever compared to a good 10mm of movement

Pic of offending bush

863e19fe.jpg

Also picked me up some rims So basically I low ball this guy 300 for a set of 4 of these. He says no, 400 with some spare unfitted tyres. Nekminut txts me again 350 with spare tyres. Rock up to his house after work, I see he's running spacers, ask about them, he says I can have them.

Then tells me he has another pair of them I can have for 200 extra. I say no. Nekminut he brings the white ones out (the "spares" dumps them on the other 4 and says 100 extra. So for 450 I get 2x 17x9 +22 and 4x 17x9 +42, 20mm bolt ons, and 2 matching pairs of spare tyres. And all the +42's all came with near new tread. Now to fit the good spares to the +22s after I refurb them silver.

Plan is to run the +22's on the front as steers, and run the 20mm bolt ons on the rear and have 2 pairs of +42's for rear duties

91f3c59d.jpg

Put a +22 on the front this arvo quickly.

525cae23.jpg

Dunno what colour to do them, kicking myself I didn't put a white one up to see if white would look good. Any opinions on colors? I was thinking silver

And thats about where it sits now

Gotta get my dump and catback on, brake booster, clutch master, throttle cable, tailshaft all back in. Then to do the little things like washer bottle and overflow, steering wheel back on, and get a set of r33 handbrake cables. Then off to get rewired, just gonna get the whole car looked over so all my accessories and the such work as it will be daily driven (hopefully if it doesnt draw too much attention) and drifted.I cant wait to finally drive it

Link to comment
https://www.sau.com.au/forums/topic/391978-my-c33-laurel/
Share on other sites

  • Replies 77
  • Created
  • Last Reply

Top Posters In This Topic

that factory rubber steering shaft spacer is piss weak you'll see a difference with the metal replacement

i'm liking this, also these too ---> Work equip 01's , need better offset not spacers :yes: .

i thought civic stud pattern was 4x100 or something ?

Link to comment
https://www.sau.com.au/forums/topic/391978-my-c33-laurel/#findComment-6238079
Share on other sites

Nah I've gone 5 stud now on the laurel hence the tri spokes

Civics are 4x100 but 96 Integra type r's come out 4x114.3 with 262mm brakes, before they went 98-01 went 5x114.3.

And I probably won't notice the difference in the steering spacer I haven't driven the laurel yet, previous owner said drop motor in and hook it up and it'll be fine, wiring loom was absolutely fooked, so had to pull it all apart again then decided to respray bay, go bigger turbo ect lol

Link to comment
https://www.sau.com.au/forums/topic/391978-my-c33-laurel/#findComment-6238129
Share on other sites

Thanks man :)

Was never meant to be such a long project but I'm glad I did respray that bay from that horrid red.

Bays midnight purple even though the photos can't quite capture all the fleck through it. Looks 100x better in rel life.

As for the turbo, its a td05, not quite sure on the trim but pretty sure it's a 20g. Guy before me made 200kw pretty easy, I'm aiming for 200kw on a low boost and then maybe a high boost a few psi more and hopefully get 220-230kw.

It's my first rwd and first turbo car so I dont want to go to silly to start with on power, and I plan on drifting it so nice responsive power should help me learn as opposed to a bigger laggy turbo.

Link to comment
https://www.sau.com.au/forums/topic/391978-my-c33-laurel/#findComment-6238644
Share on other sites

Thanks man.

Yeah it's definitely a td05, so yeah 18g most likely. Hope it makes decent power and comes on boost hard, I want something that isn't too violent when it comes on boost but I still want that kick more than a nice smooth v8 sort of power :P

As for windscreen, I'm gonna get reamed for it. I think the cheapest was Obrian glass at 580 fitted, racq was like 780 "with my customer discou t" gee thanks haha.

Link to comment
https://www.sau.com.au/forums/topic/391978-my-c33-laurel/#findComment-6240192
Share on other sites

  • 1 month later...

Bit of an update, it's Pretty much ready to be sent off for wiring now.

Brake master/booster and lines all back in ( f**k I hated life getting those nuts back on) lines hooked up, clutch master back in lines ran, nismo braided clutch line in, nismo gearbox mount in, radiator hoses cut to suit and put on, and got some scrap polished staino for an intake pipe, 2.25" no afm if this bitch doesn't dose hard I'll cry haha.

Now just gotta get my nismo low temp thermostat in, hook up my fuel lines, put my painted rocker an cam covers on and should be ready to roll once I get my rims back from work. Painter blasted and primed them, just have to paint them when he has the time, all for a carton of powers gold (eww).

And random bay snap

697bf010.jpg

Link to comment
https://www.sau.com.au/forums/topic/391978-my-c33-laurel/#findComment-6314085
Share on other sites

  • 4 months later...

haha yeah i should but i currently hate the car.

Had basically everything in the bay stolen from where the car was being stored, highmount manifold, turbo, dump pipe, gate, intercooler piping, radiator, intercooler, padded nardi and bosskit, bolt on spacers.

Im only a 4th year apprentice so the cars just sitting in my backyard, slowly collecting parts for it again. I should of stuck to hondas, could of had a k series in my civic by now lol

Link to comment
https://www.sau.com.au/forums/topic/391978-my-c33-laurel/#findComment-6514262
Share on other sites

haha dans unite for vengence indeed.

Wasnt even my house it was stolen from, was where it was being stored, and i dont talk to the dude anymore cause from what i was told when you f**k the wrong people around they f**k your shit up. I call saying "hey i'm coming round to finish the last few things up" and get told "oh half your bays missing it happened a few days ago".

And yeah its not so much finding what i need more the cash for it, i'd poured every last cent i had spare into it being an apprentice, even some of my 21st money, so its more just saving it back up, plus tax back, but knowing your over 2.5k down just sucks a fat one.

Haha hondas are cool full stop :P , my little EG hatch was 960kg with a full tank of fuel and me in it, couple that with 100kw atw and it was fun little car to drive, and they are like go karts for handling.

K series at 150-160kw atw N/A is beast, seen them run low 11s on the 1/4 with a set of slicks bolted on, and just I/H/E and some cams and a tune

Link to comment
https://www.sau.com.au/forums/topic/391978-my-c33-laurel/#findComment-6514338
Share on other sites

haha what can i say. dans a good name :P

yeah fair call mate thats pretty tough.

hope it dont take to long to get the cash back up in that case.

i agree they are fun, and ill admit ive always had a soft spot for the eg civic. would very much like an eg6 with the vtec motor in it.

chased one through the hills here in adelaide once many years ago... absolutely stomped me.... couldnt even see its tail lights after about 4 corners....

Link to comment
https://www.sau.com.au/forums/topic/391978-my-c33-laurel/#findComment-6514357
Share on other sites

Dans where its at haha

Yeah its pretty well right, gotta get a new dump made to suit new turbo, get cooler piping done again too. And redo timing belt as that was fubar'd/cut in the shitstorm. Then its back to where it nearly was, pretty much replaced everything else now. Gonna run stock cast manifold with a 3076R, internal gate for a bit less hassle from the popo.

Eg civics are the bomb, i always wanted a honda after hearing a DC2 type r integra come screaming past when i was around 15. Heard the vtec crossover and just went, yep i'm getting a honda lol.

Went from a stock as a rock Eg Si (twin cam non vtec 1.6L) to having Ek9 Type R B16b, Hytech headers and Reinhard catback (122.8db at a 5.5k freerev louder on high cam) big intake pipe, JIC coilovers, dc2r front and rear swaybars, dc2r 4 x 114.3 hub swap with 262mm twin pot brakes, stripped everything, all sound deadening, firewall matting, a/c, p/s, heater boxes.

And yeah i've shamed many a car in the twisties, back when i had the stock twin cam and king springs all round with a dc2r rear sway bar, i kept up with a stock xr6t and golf gti through the local mountains.

Just awesome little pocket rockets, i miss driving mine

IMG_0379.jpg6d8a4842.jpg

This video done on private road of course :P find another way home pizza boy ect

th_MOUNTAINRUN2.jpg

Edited by RBC33
Link to comment
https://www.sau.com.au/forums/topic/391978-my-c33-laurel/#findComment-6514638
Share on other sites

Yeah I know dude I was suss on it and I still am. End of the day what can I do... I've stewed and stewed on it, nothing I can do. Moved the car on to my place and cut the ties with the dude.

But yeah 3076r, probs make more peak power than the td05? Still haven't driven this bad boy yet, so I'm pretty keen on it. Hopefully getting dump done soon, and intercooler piping. Gotta tee it up with the local fab guys

Link to comment
https://www.sau.com.au/forums/topic/391978-my-c33-laurel/#findComment-6518049
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
×
×
  • Create New...